Avocent LCD15 Manuel d'installation rapide
Parcourez en ligne ou téléchargez le pdf Manuel d'installation rapide pour {nom_de_la_catégorie} Avocent LCD15. Avocent LCD15 2 pages. 15/17 lcd tray
Également pour Avocent LCD15 : Fiche technique (2 pages)
Imprimer la page
15/17 LCD Tray
QUICK INSTALLATION GUIDE
The following instructions will help you install your 15/17 LCD
Tray. Should you require further assistance, please contact
Avocent Technical Support.
The 1U 15/17 LCD Tray supports USB and PS/2 trackball and
keyboard, and includes a mounting kit consisting of two outer
rails with front and rear brackets attached, one rail-alignment
spacer, one IEC connector power cable and related connector
hardware.
Preparing the rack for installation
1
Review the documentation that comes with your rack
for safety and cabling information. When installing your
system in a rack, consider the following:
Ensure that the room air temperature is below 95°F and
do not block any air vents (usually 6" of air space provides
proper airflow). Starting with the heaviest, install devices
from the bottom of the rack. Never extend more than one
device out of the rack at the same time. Connect power
cords to properly wired and grounded electrical outlets,
Do not overload the power outlet when installing multiple
devices in the rack.
Installing the 15/17 LCD Tray
2
Select a 1U location in the rack and install the appropiate
cage or clip nuts. Next, loosen the two rail-adjustment
screws on each of the outer slide rails and extend the rails
to their maximum length.
Rail-adjustment
screws
F i t
t o
e n
o r t
S h
e n /
g t h
L e n
NOTE: Inner slide rails
have been removed for
illustration purposes
Adjust the outer slide-rail brackets to fit the depth of the
rack cabinet, and then use four screws to attach the front
of the slide-rail brackets to the rack cabinet. Make sure
that the slide-rail brackets extend outside of the rack-
cabinet mounting flanges.
NOTE: Do not install screws in the slide-rail bracket
middle holes. These holes are for the thumbscrews on
the front of the
.
LCD Tray
Loosely attach the back of the slide-rail brackets to the
rack cabinet, using four screws. Ensure that the slide-rail
brackets extend outside of the rack-cabinet mounting
flanges. Tighten the two rail-adjustment screws on each of
the outer rails.
Technical support and software or firmware updates:
Product manuals:
www.avocent.com/manuals
Avocent and the Avocent logo are registered trademarks of Avocent Corporation in the U.S. and other countries. All other marks are the property of their respective owners. ©2008 Avocent Corporation.
Next, loosen the front four slide-rail bracket screws
and insert the rail-alignment spacer between the finger
brackets and over the slide-rails. The rail-alignment spacer
Spacer
must wrap around the rails to align and distance them
correctly. Brackets must fit snugly against the ends of
the spacer to establish proper gap. Tighten the front four
screws and remove the spacer.
Inner part of
outer rails
extended
Now, extend the inner part of the outer rails and slide
the ball-bearing assemblies forward to the front of the
outer rails making sure it is engaged with the plastic
guide. Carefully slide the LCD Tray into the ball-bearing
assemblies in the rails.
Sliding the 15/17 LCD Tray into the rack
3
Loosen the Velcro® straps on the cable retractor to allow
free and smooth movement of the cable retractor arm.
Press the release latches, and then push the LCD Tray
completely into the rack. There will be resistance initially
as the ball-bearing assemblies align between the inner
LCD Tray
and outer rails. Pull the LCD Tray out halfway, and then
push it back in to seat the LCD Tray in the rails. Do this a
few times until the LCD Tray moves smoothly in the rails.
www.avocent.com
Remove
existing screw
CMA
thumbscrew
Push the LCD Tray into the rack, and then tighten the four
rear slide-rail bracket screws.
Remove the black rail-adjustment screw that is closest to
the rear of the rack from the outer slide-rail bracket and
discard. Attach the cable-management arm (CMA) to the
outer slide-rail bracket, using the thumbscrew attached to
the CMA.
Connecting the 15/17 LCD Tray
4
Connect the video, keyboard, and mouse connectors to
either a server or a console switch in the rack cabinet.
Connect the power cord to a properly grounded electrical
outlet or power distribution unit (PDU).
Fully extend the LCD Tray from the front of the rack
cabinet, and then route the cables within the rack cabinet,
securing them with cable straps along the way. Do not
coil the cables.
To minimize the electrical interference from the video
cable, arrange the cable in figure-eight loops. Secure the
cable in the middle with a cable strap.
NOTE: If necessary, the monitor and keyboard can
be secured inside the rack cabinet using the two
thumbscrews on the front of the LCD Tray.
(Continued on reverse side)
Latch
CMA
590-896-501B