Aqua Optima AWD001 Manuel d'instructions - Page 4
Parcourez en ligne ou téléchargez le pdf Manuel d'instructions pour {nom_de_la_catégorie} Aqua Optima AWD001. Aqua Optima AWD001 8 pages.
Également pour Aqua Optima AWD001 : Manuel d'instructions (8 pages)
Imprimer la page
Preparing a new filter
•
Remove all packaging from the water filter.
•
Do not worry about the black carbon particles on the packaging or filter, they are harmless.
•
Wipe the outside of the water filter with a damp cloth.
•
Do not use washing liquid, or anything that might taint the water.
•
For the filter to perform at its best, all air bubbles must be removed before use.
•
Submerge the water filter in a bowl of cold water and shake it
gently. When no more bubbles are released, the water filter is ready for use.
•
You might see black carbon particles in the water. Again, don't worry as they are harmless.
Removing the old water filter
•
Use the handle to lift the lid off the filter holder (Fig.1)
•
Removing the filter holder will need two hands – put the thumbs inside the walls of the filter
holder, put the fingers on the outside of the rim, and gently lift upwards.
•
Don't turn the filter holder upside down. Try to keep the filter upright at all times.
•
Grip the bottom of the filter with the other hand.
•
Turn the filter clockwise (about 1.5cm), to bring the tabs on the top of the filter into the bulges
at the sides of its holder, then bring the filter down and out of the filter holder.
•
Gently ease the seal off the underside of the water tank (Fig.3)
•
Clean the seal and water tank with a damp cloth. Don't use washing-up liquid, or anything that
might taint the water.
•
Fit the seal snugly to the underside of the filter holder. The lugs in the bottom of the filter holder
fit into the slots in the seal (Fig.3).
Fitting the new filter
•
Align the tabs on the top of the filter with the bulges on the underside of the filter holder.
•
Lift the filter up and into its holder, push it gently against the seal, and turn it anticlockwise
(about 1.5cm) to lock it into the filter holder.
•
Lower the filter holder into the water tank.
Filling the water tank
•
Lift the lid off the filter holder (if it's not already off).
•
Use a jug to pour water into the filter holder. If you don't have a big enough jug, clean out your
electric kettle and use that – most kettles hold about 1.7litres. Two jugs, two kettles, or a jug and
a kettle makes life even easier.
* Don't pour directly on to the filter.
Air Locks
•
To prevent air locks in the cooling unit (underneath the water tank) you need to keep the tap
open while you're filling the water tank, so that the incoming water drives the air out.
•
Put a container that holds at least a litre under the spout.
•
If the container is tall enough, use it to push the tap back against the wall of the cooler. If not
you'll have to hold the tap open with a finger.
•
Either way, push the tap back against the wall of the cooler and keep it there.
•
Pour water into the top of the filter holder.
•
Keep pouring until about to litre comes out of the spout, then let the tap close.
•
That should be enough to clear all air out of the system.
•
With the tap closed, keep pouring into the filter holder until the water tank is full, and the filter
holder is full to within about a centimeter of the rim.
•
Water flow through the filter will get slower, as the water tank and the filter fill up.
•
Put the lid on – the edges of the lid should be just clear of the water.
AWD001_IM_without_elec-timer_JULY2011.indd 4
3.
2013/07/11 09:52:56 AM