DH Lifelabs HD100-120BL Manuel d'instruction - Page 3

Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} DH Lifelabs HD100-120BL. DH Lifelabs HD100-120BL 14 pages.

Imprimer la page

Your safety is important to us.

Read all safety instructions before you use the device.

WARNING! TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR INJURY PLEASE ADHERE TO THE FOLLOWING:

This device must be installed in accordance

with current local wiring and building

regulations, and installed by a qualified

licensed eletrician.

WARNING: Ensure the device is fully

assembled in accordance with the instructions

before use. If casing is removed or handled

improperly the internal components of the

unit may cause harm or become permanently

damaged.

Use this unit only in the manner intended by

the manufacturer.

This device complies with the maximum

allowable concentration of ozone of 0.05 parts

per million by volume (ppmv) in a 24 hour

period.

The unit is intended to be permanently

connected to the power supply.

Ensure that the mains supply (voltage,

frequency, and phase) complies with the

devices rating label.

This device is not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities, or lack of

experience and knowledge, unless they

have been given supervision or instruction

concerning use of the device by a person

responsible for their safety.

The device should be provided with a fused

spur, isolator switch capable of disconnecting

all poles, having a contact separation of at

least 3mm.

The device is designed for dry, internal

location only. Do not allow the area around the

device to become damp or wet.

All metal parts in contact with this device

MUST be earthed, including any wall covering.

Always use the device with the accessories

provided.

Do not move the device while it's wired.

Do not use the device with a damaged wires.

It must be replaced by a suitably qualified

service engineer in order to avoid a hazard.

If the device is not working properly, has

received a sharp blow, has been dropped or

damaged, do not use the device and contact

customer support for repair.

Troubleshooting and internal maintenance

must be performed by qualified service

personnel.

Wear gloves when inspecting and cleaning the

device.

Do not use any power wash equipment for

cleaning on or near this device.

Do not use the device for drying hair or other

items.

Do not obstruct air inlets or outlets. Do not

cover the device while in use.

Do not use the device in the following places:

•

Where the ambient temperature is below

-10°C or above 40°C

•

Where the device may come into direct

contact with water

•

Where the device is under direct or strong

sunlight

•

Where condensation may form within the

device.

•

Locations where corrosive, neutral, or

reductive gases are present.

This device is intended for indoor use only.

Consult local and national accessibility codes

and regulations for relevant installation

guidelines. Conformity and compliance is the

responsibility of the installer.

Make sure electricity is switched off at the

main panel before installing, maintaining or

cleaning this device.

Ensure that the conduct and wires are long

enough to connect to the backplate and the

terminal block.

Ensure no pipe work (gas, water, air) or

electrical cables, wires or ductwork are located

directly behind the drilling/mounting area.

Choose a completely flat, vertical wall capable

of supperting the full weight of the device.

Install the device in a location where it will be

easy to use and ensure that there is adequate

space around the device for cleaning and

maintenance.

Avoid installing the device in locations where

people or doors might bump into the device.

If the device is installed too low, water may

splash onto the device when the floor is being

cleaned. (The bottom of the device must be

mounted at least 15 inches/381mm above the

floor).This is also required to gain access to the

HEPA filter for cleaning and/or replacement.

Check that the electrical supply corresponds to

that shown on the rating sticker of device. Do

not connect the device to any electrical supply

other than that stated on the rating label of

the device. Permanent damage or improper,

unsafe operation of the device may result.

To avoid contact with water from the user's

hands, do not install the device above any

electrical equipment.

Do not use sealant when fixing the device

to the wall. This device is not suitable for

mounting onto porous wall surfaces (e.g.

plaster) without a back panel, to avoid

discoloring or damage to unprotected walls.

Before installaiton, please consider the flow

of traffice through the washroom. We are not

recommended to put the device in an area of

the wahsroom that makes people steps in front

of high footfall areas. You can install the device

as near to the sinks as possible to minimize

water spillage onto the floor from hands. You

should also consider the mounting height of

the devices, and who will be using it.

Read all safety instructions in the

instruction manual, and on device.

SAVE THESE INSTRUCTIONS.