Dell EMC PowerSwitch N3048ET-ON Comment mettre à jour le micrologiciel - Page 17

Parcourez en ligne ou téléchargez le pdf Comment mettre à jour le micrologiciel pour {nom_de_la_catégorie} Dell EMC PowerSwitch N3048ET-ON. Dell EMC PowerSwitch N3048ET-ON 21 pages.

Imprimer la page
Dell EMC PowerSwitch N3048ET-ON Comment mettre à jour le micrologiciel
Upgrade Dell EMC Networking N3000E-ON Switches
Console#show switch
Management Standby
SW
Status
--- ---------- --------- ------------- ------------- ------------- -----------
1
Stack Mbr
2
Stack Mbr
3
Mgmt Sw
4
Stack Mbr
5
Stack Mbr
6
Stack Mbr
Console#show ver
Machine Description............... Dell EMC Networking Switch
System Model ID................... N3048EP-ON
Machine Type...................... Dell EMC Networking N3048EP-ON
Serial Number.....................
Manufacturer...................... 0xbc00
Burned In MAC Address............. 0090.BC06.A571
System Object ID.................. 1.3.6.1.4.1.674.10895.3060
SOC Version....................... BCM56340_A0
HW Version........................ 5
CPLD Version...................... 20
Image File........................ N3000AdvLitev6.5.3.6
Software Capability............... Stack Limit = 8, VLAN Limit = 1024
unit active
---- ----------- ----------- -------------- --------------
1
6.5.3.6
2
6.5.3.6
3
6.5.3.6
4
6.5.3.6
5
6.5.3.6
6
6.5.3.6

Upgrade mixed stack of N3132PX-ON, N3000E-ON and N3000 Series switches (Adv-Lite)

To upgrade a mixed stack of N3132PX-ON, N3000E-ON and N3000 series switches from 6.x.x.x to 6.5.3.6 version
or later uses the procedure below. An annotated upgrade example is shown following this section.
1. Back up your configuration from mixed stack.
2. Upgrade using telnet or SSH require default enable authentication method or enable password in current
configuration. If not configured, follow steps below to configure an enable password:
console#configure
console(config)#enable password <password>
console(config)#exit
console#copy running-config startup-config
3. Download the 6.5.3.6 firmware image (N3000N3100AdvLitev6.5.3.6.itb) to the mixed stack
4. Activate 6.5.3.6 firmware.
5. Reload the mixed stack.
6. Verify the firmware version on stack of N3000E-ON, N3000 and N3132PX-ON Series switches via show
switch and show version command output.
Preconfig
Status
Model ID
Oper Stby N3132PX-ON
N3132PX-ON
N3048EP-ON
N3048EP-ON
N3048P
N3048P
backup
current-active next-active
6.5.3.6
6.5.3.6
6.5.3.6
6.5.3.6
6.5.3.6
6.5.3.6
6.5.3.6
6.5.3.6
6.5.3.6
6.5.3.6
6.5.3.6
6.5.3.6
Plugged-in
Switch
Model ID
Status
N3132PX-ON
OK
N3132PX-ON
OK
N3048EP-ON
OK
N3048EP-ON
OK
N3048P
OK
N3048P
OK
6.5.3.6
6.5.3.6
6.5.3.6
6.5.3.6
6.5.3.6
6.5.3.6
Page 13
Code
Version
6.5.3.6
6.5.3.6
6.5.3.6
6.5.3.6
6.5.3.6
6.5.3.6