Dialog Semiconductor DA9231 Manuel de l'utilisateur - Page 11

Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} Dialog Semiconductor DA9231. Dialog Semiconductor DA9231 18 pages. Fuel gauge development kit

Imprimer la page

UM-PM-039

DA9070 / DA9231 Fuel Gauge Development Kit

(LDO_1)

VDD_SYS_M

J11

VDD_LDO2/

VDD_SYS_M

(LDO_2)

J12

BST_LD/ +/ S+/ S-/ -

(VO_BST)

J13

VBAT_DIV/

GND_DIV/ I_MON/

TMP_SNS/ AGND

J14

SW_BYPASS/

VDD_PWR/

SW_USE/ S+/ S-/

PGND

J16

S+/ S-

(VDD_SYS_M)

J17

P_FLT, WD, S_FLT,

RIN_N, ITER_C,

AGND, ILIM_C,

AGND, ILIM_P,

AGND, ROUT_N,

MODE

J18

LDO0_LD/ +/ -

(LDO0_LD)

J19

LDO1_LD/ +/ -

(LDO1_LD)

J20

LDO2_LD/ +/ -

(LDO2_LD)

J21

+/ S+/ S-/ -

(VO_BUCK_M)

User Manual

(VDD_LDO1) to VDD_SYS_M of DA9070.

Install J11 jumper will connect LDO_2 input

(VDD_LDO2) to VDD_SYS_M of DA9070.

+ and - are terminals for connecting external load to

the Boost output; When BST_LD (pin 1) is short to +

pin on J12, the on-board load resistor will be used as

the Boost output load. S+ and S- are kelvin sense

points for the Boost output. For output voltage

measurement during efficiency test, S+ and S- should

connect to multi-meter for better accuracy.

Sense points. For probe only.

DA9070 power input (VDD_PWR) supply selection

and voltage sense. VDD_PWR can directly connect

to the 5V_USB rail by shorting J14 pin-1 to pin-2;

VDD_PWR can also connect to the 5V_USB rail

though load switch U1 by shorting J14 pin-2 to pin-3.

The load switch is controlled by the MCU during

battery profiling. For evaluation use jumper positions

1 and 2. J14-S+ and J14-S- pins are kelvin sense

points of DA9070 input VDD_PWR.

S+ and S- are kelvin sense points for DA9070

VDD_SYS.

Sense points. For probe only.

+ and - are terminals for connecting an external load

to DA9070 LDO0 output; When pin-1 is shorted to the

+ pin on J18, the on-board load resistor will be used

as the LDO0 output load.

+ and - are terminals for connecting external load to

DA9070 LDO1 output; When pin-1 is shorted to + pin

on J19, the on-board load resistor will be used as the

LDO1 output load.

+ and - are terminals for connecting external load to

DA9070 LDO2 output; When pin-1 is shorted to + pin

on J20, the on-board load resistor will be used as the

LDO2 output load.

+ and - are terminals for connecting an external load

to DA9070 Buck output; S+ and S- are kelvin sense

points for DA9070 Buck output. For output voltage

measurement during efficiency test, S+ and S- should

connect to multi-meter for better accuracy.

Revision 2.1

11 of 18

NDA Confidential

28-Oct-2018