Aquant STANDARD Series Manuel d'installation et d'entretien - Page 3
Parcourez en ligne ou téléchargez le pdf Manuel d'installation et d'entretien pour {nom_de_la_catégorie} Aquant STANDARD Series. Aquant STANDARD Series 11 pages. Flat underwater light
Imprimer la page4. ASSEMBLY:
The floodlamp is supplied with 2.5m of cable. It should be inserted through the conduit body(Fig 4), leaving
approximately 1.5m of cable in order to be able to remove the floodlamp to the border of the swimming pool if
handing or lamp change is required(Fig 1).
Wind the cable in counter-clockwise direction under the screen fastening clamps(Fig 5). Firmly secure the gland
seal nut (Fig 6).
In order to secure the floodlamp to the crosshead mount, ensure that the word "TOP" is located on the upper part.
First, insert the lower clamp of the screen in the crosshead mount.
Then, press on the upper part until the floodlamp is firmly inserted in the crosshead mount.
5. MAINTENANCE:
To r e m ove the floo d la mp to t h e edge of the swimming p ool ( F ig . 1) Insert a screwdriver through the upper hole of the
ornament and press on the spline of the mount until the floodlamp is released.(Fig 7-8).
Pull up on the floodlamp until it is released from the lower groove and can be removed from the seimming pool.
Unlock the screw, Dismount the floodlamp by turning the key in counter-clockwise direction(Fig 9).
Pull on the lamp to separate it from the lamp holder. Connect the new lamp(Fig 10).
VERY IMPORTANT: To change the lamp, always use the cardboard protector and never touch the new lamp with your bare
hands.
Then, assemble the floodlamp in the opposite order of that described. Make sure that the butt joint and the transparent lens are
iinserted properly in the screen seat.
Align the word "TOP" on the ornament with the word "TOP" on the screen fastening.
Turn the ornament slightly to the right until it is fitted with the screen.
Wind 1..5m of cable in counter-clockwise direction under the screen fastening clamps. (Fig 5)
Atten ti on:
B efore any handling e n s ur e that the r e is N O voltage s upp lied to the floo dlamp .
T h e n ew lamp should h ave the sa m e ch a r a c te ris ti c s as t h at su pp lie d with t h e floo d la mp , (75W 12V halogen lamp).
In orde r to e n s ur e full watertightness, clea n the seat of the floodlamp lens joint or r e pla ce this if any permanent
deformation or notches are visible.
6. START -U P:
Ensure t h at the voltage the lamp re c e iv es is n eve r greater than 12 V.
The floo d lamp sho u ld o n ly operate und erwater w h ile se cu re d to the verti cal walls of the p ool. N ever switc h on the
floo d la mp if it is not un de r water.
7. SAFETY WARNI N GS:
The persons who are i n charge of assembly should have the required qual if icatlons f or t his t ype of work.
If the end cab l e of t his li gh t fitti ng is damaged, it should only be replaced by the manufacturer,
its t echnica l service or by a similar l y qualified person, to avoid any danger.
Avoid making contact w i th t he elec t r i c vo lt age.
Comply w it h t he curren t standards regarding accident preven ti on.
In this regard, t he IEC 364-7-702 s t andards must be observed. WIRING I N BUI L DI NGS.
SPECIAL WI RI NG. SWIMMING POOLS.
Any operation re l ated t o t he maintenance or replacemen t o f parts should be performed w it h
t he flood l amp disconnec t ed from the elec t ric power system.
Do not handle w it h we t f ee t .
The manufacturer is no t responsib l e in any c i rcums t ances for assembly, ins t allation or s t ar t- up o f
any electric componen t s which have been inserted or handled at l ocations other than Its own premises.