Chrosziel MagNum MN-100 Manuel de référence rapide - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel de référence rapide pour {nom_de_la_catégorie} Chrosziel MagNum MN-100. Chrosziel MagNum MN-100 2 pages. Single-channel wireless lens control system

Imprimer la page

Menu Navigation

Power button, press for more than 2

seconds to switch hand unit off; can

be used to exit a sub menu as well

Select menu item (up)

Press center button to enter set up

menus

Edit values (left = -; right = +)

Select menu item (down)

Set Up the Record Start/Stop Trigger*

Select whether hand unit with ID 1 or

Record Trigger

2 can trigger the record signal

Enabled ID:

Matching :

Select mode entry and modify trigger

Mode: < Pulse >

mode with -/+ buttons

Start

Stop

*Setting is stored in the motor box in

Save&Exit

Cancel

the non volatile memory and is

editable on hand unit 2 as well

Set Up Motors & Servo Lens Control

Motor 1: Enter configuration menu of

Motor Setup

the motor output

Motor 1 (F)

Motor 2: No support in combination

Motor 2 (I/Z)

with MN-100 motor controller!

Servo Lens Setup

Servo Lens Setup*: No Support on

off

MN-100 motor controller!

< Back

*Setting is stored in the motor box in the non-volatile memory

Calibrating motors in manual "Photo Lens" mode

Unlike commonly used lenses in the film industry the lenses for still cameras do not feature physical end stops on their gears. Therefore it is

not possible to calibrate so-called photo lenses by the motor controller automatically. The MagNum motor controller addresses this issue by

allowing a desired motor socket to be configured as "Lens Type = photo". The manual procedure is as follows:

mount motor as normal on the support rod and engage it to the lens in a middle position of the available range of movement

press calibration button once; motor LEDs start flashing fast but motor will not start moving on its own as it would in "Cine" mode

move motor by hand by manually turning lens to both of the limits (infinite & near) of the lens gear

turn motor back to a middle position after

press calibration button a second time , motors will now start moving measuring automatically lens parameters between the two chosen

end points

after this calibration is finished

Hints:

As most motors show a certain amount of play/backlash, turn the motor a little further than normally necessary in order to compensate this

play regarding the correct end stops on both limits.

Some motors do not allow turning manually in both directions – in this case engage the motor on one limit and turn the motor just in the

direction to the opposite limit.

Main Screen

Display of power supply voltage on

Cam. Pow.: 13.5V

receiver side*

Data always visible, from left to right:

ID 1

Battery indicator

Hand unit ID (can be 1 or 2)

RF signal strength indicator

Bidirectional

link

indicator:

Green = connection OK – may go

red intermittently

*Display can be disabled/enabled on menu entry "Display Options"

Setup Scales - Reverse Scale Direction*

If switched to "On", wheel or slider

Reverse Wheel

operate reversed. Operation direction

off

depends on how motors are mounted

and on the preferences of the user

Reverse Slider

off

*Setting is stored in the hand unit and

is independent from setting in second

Save&Exit

Cancel

hand unit.

Set Up Motor Output*

M1 Set Up

Link to: Assigned function (Focus / or

Iris)

Link to

Mode: Switch to dimmer mode here.

Mode

motor

Dimmer cable can be controlled.

Range

Lens

Range: Switch to 3D Rig mode if

Direction

norm

required

Play/ Safety

0 / 0

Direction : Reverse motor direction

Full

Torque

Play/Safety: Modify play (backlash)

Lens Type

Photo

compensation for heavily used motors

Save&Exit

Cancel

with a large amount of play in the

gearbox.

Modify the safety distance, the motor stays away from the

mechanical Lens End Stops (S3D Rigs). Torque: Reduce torque of

the motor to mid (50%) or low (25%).

Lens Type: Cine = End stops will be calibrated automatically; Photo

= End stops are calibrated manually.

*Setting is stored in the motor box in the non-volatile memory and is

editable on hand unit 2 as well

Setup Screen

(press Center Button from Main Screen)

Switch LED swan-neck light on/off

Light ON/OFF

Select radio channel and range

Radio Channel

(MHz or GHz)

Record Trigger

Select camera record start/stop mode

Scales

Reverse wheel &/or slider operating

Calibrate Motors

direction

Start motor calibration remotely

Motor Setup

Motor setup (torque ; direction; play

Set Up Hand Unit

correction ...)

Select hand Unit ID, serial socket

mode, calibrate the hand wheel &

slider, assign user keys

Start Motor Calibration remotely

Select a motor with up/down buttons and

Motor Calibration

then

press center button of the keypad,

automatic or manual end stop calibration is

Cal. Focus

initiated.

Cal. Iris (Zoom)

< Done

Setup Hand Unit

Ctrl. ID: Switch the hand unit ID to 2 if

Set Up Hand Unit

two controllers shall be used (split

Ctrl. ID < >

functions F & I to two controllers). ID1

controls F & I by default. If a second

Left-Handed

unit is set to ID 2, this unit will take

Serial Socket

over control of motor I by its hand

Display Options

wheel if MN-200R motor controller is

Load Defaults

used.

You must not have more than one

hand unit set to the same ID!

Wheel/Slider Cal.

Left-Handed: If "yes", the Display is

< Back

rotated by 180° in order to make left-

handed operation more easy

Serial Socket: No support!

Display Options: Select, whether several displays shall appear on

the main screens info area (i.e. Cam.-Power)

Wheel/Slider Cal.:

Basic calibration of the hand wheel to its

respective mechanical operating range

Spreading of the Wheel

Spreading is done by pressing one of the user keys 1 .. 4. Spreading function needs to be assigned to the desired user keys*. Default mode

is*: U1-4 spread the wheel scale. So there are four different spreading setups available.

To set a spreading:

a) Move wheel to the desired first starting point, press a user key for more than 1 second and keep pressing during the procedure

b) Respective yellow LED starts flashing

c) Move wheel to the desired second point, release the user key

d) Spreading is applied between the two points, respective yellow LED lights up continuously

To switch off a spreading: Press the user keys for which a spreading is activated less than 1 second, respective yellow LED goes off.

To recall a formerly programmed spreading: Press the same user key again for less than 1 second.

*Currently the assignment of spreading function is fixed to the default set up. Later software versions will allow to assign different functions

to the 4 user keys.

Set the Frequency Range and the Radio Channel

Set Radio

Chan.:

Freq. :

2422.75

Spectrum

Please note: When this screen is visible the MagNum wireless

connection is temporarily disconnected as the hand unit scans

through all available RF channels at this time searching for

possible frequencies. For GHz range (Channels 5 - F) internal

antennas are used.

Frequency Table:

Channel

Center Frequency

n.a.

2.400.75 GHz

2.40375 GHz

2.40975 GHz

2.42275 GHz

2.44075 GHz

2.44375 GHz

2.44975 GHz

2.46275 GHz

2.47075 GHz

2.47375 GHz

2.48175 GHz