AquaScape Spillway Basin 78205 Instructions et entretien - Page 4

Parcourez en ligne ou téléchargez le pdf Instructions et entretien pour {nom_de_la_catégorie} AquaScape Spillway Basin 78205. AquaScape Spillway Basin 78205 12 pages.

Imprimer la page

Installation

INSTALL PLUMBING

• The Spillway Bowl and Basin allows for either a ¾" or 11/2"

water inlet. The pre-installed bulkhead reducers provide a

¾" threaded connection at the

bottom of the fountain. If desired,

the reducers can be removed

to expose a 11/2" threaded inlet,

allowing for higher flow rates

with more dramatic water flow.

• If a ¾" inlet is desired, thread

the included multi-hose adapter

fitting (¾", 1", 11/4") into the

reducer inlet at bottom of

fountain (Ex. 1).

• If a 11/2" inlet is desired, remove

the reducer fittings from the

inside and bottom of the

fountain (Ex. 2). Then, thread

a compatible 11/2" fitting (not

included) into the bottom of the

fountain.

TIP - If desired, plumbers tape or silicone (not

included) can be used on fitting threads to help

provide a watertight connection.

INSTALL PIPE/TUBING

• Attach pipe/tubing (not included)

to the fitting installed at the

bottom of the fountain (Ex. 3). A

hose clamp (not included) can be

used to secure the connection.

• If installing the Spillway Bowl

Stand, use the integrated

plumbing slot on the stand to run

the pipe to the underside of the

Spillway Bowl (Ex. 4).

TIP: In some instances

the pipe/tubing may be

tight or difficult to connect

to the fitting. If this is the

case, it is recommended to heat

the pipe with a hair dryer or dip it

for a few seconds in very hot water.

Lubrication such as silicone grease

or olive oil can also be used.

INSTALL LIGHTING (OPTIONAL)

• The Spillway Bowl and Basin provide the option of installing

low-voltage underwater lighting. It is recommended to use

the Aquascape Garden and Pond 1-Watt LED Spotlight

(#84031) or Waterfall and Up Light (#84032).

• If installing a light, remove the

pre-installed light chase plug from

the bottom of the fountain (Ex. 5)

and locate the rubber light chase

insert packaged with the plumbing

components.

• Feed the low-voltage light cable

through the light hole from the

top of the fountain until the light

is set in the desired location.

• Insert the cable firmly into the

rubber light chase insert (Ex. 6).

Then, secure the rubber insert in

the light hole from the top (Ex. 7).

• Run the light cable from the

bottom of the Spillway Bowl

or Basin to a compatible low-

voltage transformer.

TIP - If desired, silicone

sealant (not included)

can be applied to help

provide a water-tight

seal.

CONNECT THE PUMP

• Connect the pipe/tubing to a

compatible pump (not included)

(Ex. 8). It is recommended to

use an Ultra 2000 Water Pump

or larger. A hose clamp (not

included) can be used to secure

the connection.

INSTALL STANDPIPE

Ex. 3

• The Spillway Bowl and Spillway

Basin each include a PVC

standpipe and tee fitting to

prevent the feature from draining

when the pump stops and

provide optimal water flow while

in use.

• Install the standpipe by threading it into the fitting at the

center of the fountain. The included standpipe is not

Ex. 4

compatible with the expanded 11/2" water inlet. If desired, a

11/2" diameter standpipe can be fabricated using commonly

available rigid PVC pipe.

☎

US (866)877-6637 |

☎

CAN (866)766-3426 | aquascapeinc.com

Ex. 5

Ex. 6

Ex. 7

Ex. 8