Panasonic WV-CP470 Series Manuel d'utilisation - Page 10
Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Panasonic WV-CP470 Series. Panasonic WV-CP470 Series 13 pages. Colour cctv cameras
Également pour Panasonic WV-CP470 Series : Manuel d'utilisation (13 pages), Spécifications (2 pages)
Imprimer la page
Manual Fine Adjustment for AWC (ATW)
You can set the white balance items manually.
1. To set MASK SET, proceed as described in steps 2 to 4 of "ALC mode with SUPER-D2
OFF and ELC mode".
2. Move the cursor to R.
3. Press L or M to obtain the optimum amount of red gain.
4. Move the cursor to B.
5. Press L or M to obtain the optimum amount of blue gain.
Note: When you need to set MASK SET, re-adjust to obtain the optimum amount of red and
blue gain.
8. Motion Detector Setting (MOTION DET)
The motion detector detects the moving objects in the scene by monitoring changes in
brightness level. You can select the level of sensitivity for motion detection.
When this camera is connected to a compatible intelligent CCTV system, the camera trans-
mits an alarm signal by multiplexing it with the video signal.
1. Move the cursor to MOTION DET and
select ON.
The factory default setting is OFF.
2. Press I. The MOTION DETECT
menu appears on the monitor screen.
3. Move the cursor to MASK SET and press I. MASK SET lets you set 48 mask areas.
To set MASK SET, proceed as described in steps 2 to 4 of "ALC mode with SUPER-D2
OFF and ELC mode".
4. Move the cursor to ALARM and select ON or OFF to set the alarm for DISPLAY MODE.
Note: When using the WV-RM70, WV-CU550 series, WV-CU161 or WV-CU360 controller
with this model, select OFF for ALARM.
5. Move the cursor to DISPLAY MODE and press I to see the current setting. The
masks that detect the brightness changes start blinking.
6. To raise detection sensitivity, press I to return to the MOTION DETECT menu.
7. To obtain the optimum detection level, move the "I" cursor to adjust the level.
8. Repeat the procedures above to obtain a satisfactory setting.
Notes:
• When the camera is not used in a Panasonic Intelligent CCTV System, select OFF.
Otherwise, video equipment may malfunction because of the alarm signal misinterpreta-
tion for a time code signal.
• The motion detector may malfunction when the lightning equipment continuously turns
on and off, or when ELC mode is selected for ALC/ELC.
• Set MASK SET over the areas where leaves or curtains etc. are swaying.
• Adjust the detection level on the menu to prevent misinterpretation under low light con-
ditions with noise.
• It takes about 0.2 seconds for the alarm signal to reach the VTR's alarm terminal after
the camera detects the moving object.
• The motion detector is not specifically intended to prevent theft or fire.
9. Lens Drive Signal Selection (LENS DRIVE)
This item is used to select the type of auto iris lens drive signal to be supplied to the lens
from the auto iris lens connector.
1. Move the cursor to LENS DRIVE.
The factory default setting is DC.
2. Select DC if you are using the auto iris lens that requires a DC drive signal.
Select VIDEO if you are using the auto iris lens that requires a video drive signal.
10. Special Menu
This menu lets you adjust and set up the video signal of the camera to meet your require-
ments.
Move the cursor to END in the bottom
line of the CAM SET UP menu and
press L and M simultaneously
(holding down L and press M) for 2
seconds or more. The SPECIAL menu
appears on the monitor screen.
10-1. Camera Picture Upside Down Positioning (UP SIDE DOWN)
1. Move the cursor to UP SIDE DOWN.
2. Select ON when you want to turn the picture upside down.
10-2. Chroma Level Setting (CHROMA GAIN)
1. Move the cursor to CHROMA GAIN.
2. While observing the vectorscope or colour video monitor, move the "I" cursor to adjust
the chroma level.
10-3. Aperture Gain Setting (AP GAIN)
1. Move the cursor to AP GAIN.
2. While observing the waveform monitor or colour video monitor, move the "I" cursor to
adjust the aperture gain level.
10-4. Pedestal Level Setting (PEDESTAL)
1. Move the cursor to PEDESTAL.
2. While observing the waveform monitor or colour video monitor, move the "I" cursor to
adjust the pedestal level (black level).
** MOTION DETECT **
LEVEL
DISPLAY MODE
ALARM
MASK SET
RET
** CAM SET UP **
CAMERA ID
OFF
ALC/ELC
ALC
SHUTTER
---
AGC
ON(DNR-H)
SENS UP
OFF
SYNC
INT
WHITE BAL
ATW1
MOTION DET
OFF
LENS DRIVE
DC
END
SET UP ENABLE
........I
-
+
OFF
END
** SPECIAL **
UP SIDE DOWN OFF
CHROMA GAIN
AP GAIN
PEDESTAL
BW
BURST(BW)
CAMERA RESET / PUSH SW
RET
END
....I....
....I....
.I.......
-
+
OFF
ON