Panasonic PT-L6600E Manuel d'utilisation - Page 8
Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Panasonic PT-L6600E. Panasonic PT-L6600E 50 pages. 3600 ansi lumens sxga lcd projector 4200 ansi lumens xga lcd projector
Également pour Panasonic PT-L6600E : Brochure & Specs (6 pages), Brochure & Specs (6 pages)
Imprimer la page
Precautions on handling
Cautions regarding transportation
Be sure to attach the lens cover before transporting the
projector.
The projection lens is extremely susceptible to vibration
and shocks. When carrying the projector, be careful not to
subject to excessive vibration or shock while under
transport.
Cautions regarding setting-up
Observe the following at all times when setting up the
projector.
Avoid setting up in places which are subject to
vibration or shocks.
If the projector is set up in locations with strong vibration,
such as near a motor, or if it is installed inside a vehicle or
on board a ship, the projector may be subjected to vibration
or shocks which can damage the internal parts and cause
malfunctions or accidents. Accordingly, set up the projector
in a place which is free from such vibrations and shocks.
Do not set up the projector near high-voltage power
lines or near motors.
The projector may be subject to electromagnetic
interference if it is set up near high-voltage power lines or
motors.
If installing the projector to the ceiling, ask a qualified
technician to carry out all installation work.
If the projector is to be suspended from the ceiling, you
will need to purchase the separate installation kit (Model
No.: ET-PKL6500/S). Furthermore, all installation work
should only be carried out by a qualified technician.
This product cannot be used at altitudes of 1,400 m or
more above sea level. If it is used as is, there may be an
adverse effect on component service life and so on.
Notes on use
If using this projector more than 8hours/day (continuous
operation), special measures will be necessary to use
this projector. Please consult your dealer or Authorized
Service Centre about preparations.
In order to get the best picture quality
If outside light or light from indoor lamps is shining onto
the screen, the images projected will not have good
contrast. Draw curtains or blinds over any windows and
turn off any fluorescent lights near the screen to prevent
reflection.
Depending on the environment where used, hot air from
the cooling fan vent may in rare cases cause disturbances
on the screen.
Do not touch the surfaces of the lens with your bare
hands.
If the surface of the lens becomes dirty from fingerprints
or anything else, this will be magnified and projected onto
8
the screen. Moreover, when not using the projector, cover
it with the accessory lens cover.
About the screen
If the screen you are using is dirty, damaged or discolored,
attractive projections cannot be obtained. Do not apply
any volatile substances to the screen, and do not let it
become dirty or damaged.
Lamp
A mercury lamp with high internal pressure is used as the
light source for this equipment. High-pressure mercury
lamps have the following characteristics.
• If the lamp deteriorates due to shock, scratching or the
passage of time during use, it may rupture with a loud
noise, or enter the unlit state and end its service life.
• Service life varies significantly due to individual lamp
differences and use conditions.
• Exceeding the replacement period will increase the
probability of rupture.
About the liquid crystal panel
The liquid crystal panel of the projector is built with very
high precision technology giving you fine picture details.
Occasionally, a few non-active pixels may appear on the
screen as a fixed point of blue, green or red.
Please note that this dose not affect the performance of
your LCD.
About optical parts
If the projector is subjected to a continuous use for more
than 6 hours every day, you may have to replace optical
parts, such as LCD panels or polarizers within less than
one year. When you use the projector in such a case, ask
your dealer or an Authorized Service Center for details.
Before carrying out cleaning and
maintenance, be sure to disconnect the
power cord plug from the wall outlet.
Wipe the cabinet with a soft, dry cloth.
If the cabinet is particularly dirty, soak the cloth in water
with a small amount of neutral detergent in it, squeeze
the cloth very well, and then wipe the cabinet. After
cleaning, wipe the cabinet dry with a dry cloth.
If using a chemically-treated cloth, read the
instructions supplied with the cloth before use.
Do not wipe the lens with a cloth that is dusty or which
produces lint.
If any dust or lint gets onto the lens, such dust or lint
will be magnified and projected onto the screen. Use
a blower to clean any dust and lint from the lens
surface, or use a soft cloth to wipe off any dust or lint.