Panasonic RX-D45 Manuel d'utilisation - Page 6

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Panasonic RX-D45. Panasonic RX-D45 8 pages. Portable stereo cd system
Également pour Panasonic RX-D45 : Manuel d'utilisation (8 pages), Manuel d'utilisation (20 pages)

Imprimer la page

Using the clock and timers

Setting the clock

This is a 24-hour clock.

Press [CLOCK/TIMER].

Each time you press the button:

CLOCK

Within 5 seconds or so

Press [– /2] or [6/+] to set the time.

Holding down the button will speed up the time selection.

Press [CLOCK/TIMER] to ﬁ nish setting the time.

Displaying the clock

Press [CLOCK/TIMER] to display the clock for few seconds.

✒

Note

• Reset the clock regularly to maintain accuracy.

• When the unit is in standby mode and it is powered by batteries, clock will not

be displayed.

Using the play timer

You can set the timer to come on at a certain time to wake you up.

✒

Preparation

• Turn the unit on and set the clock.

• Prepare the music source you want to listen to; disc or radio source, and set

the volume.

Press [CLOCK/TIMER] repeatedly to select the play timer.

Within 5 seconds or so

Press [– /2] or [6/+] to set the

starting time.

Press [CLOCK/TIMER] to conﬁ rm.

Repeat steps 2 and 3 to set the ﬁ nishing

time.

To activate the timer

Press and hold [– # PLAY] to turn on the timer.

# PLAY

Press [TAPE/OFF] to turn off the unit.

Change the

Repeat steps 1 to 4 and 6 (Z see above).

settings

Change the source

1. Press and hold [–# PLAY] to clear the timer

or volume

indicator from the display.

2. Make changes to the source or volume.

3. Perform steps 5 and 6 (Z see above).

Press [CLOCK/TIMER] repeatedly to select # PLAY.

Check the settings

(when the unit is on

or in standby mode)

Cancel

Press and hold [–# PLAY] to clear the timer indicator

from the display.

✒

Note

• The play timer will start at the preset time, with the volume increasing

gradually to the preset level.

• The timer comes on at the set time every day if the timer is on.

• The unit must be in the standby mode for the timer to function.

• If you turn the unit off and on again while a timer is functioning, the ﬁ nish time

setting will not be activated.

Using the sleep timer

This function enables you to turn off the unit automatically after the set time

except in tape mode.

Press [CLOCK/TIMER] repeatedly to select "SLEEP".

Press [– /2] or [6/+] to select your desired time (in minutes).

To cancel

Press [CLOCK/TIMER] repeatedly to show the remaining time, and press

[–/2] or [6/+] to select "OFF".

Changing the remaining time

Press [CLOCK/TIMER] repeatedly to show the remaining time, and press

[–/2] or [6/+] to select your desired time.

✒

Note

• The play and sleep timer can be used together.

• The sleep timer always has priority. Be sure not to overlap timer settings.

# PLAY ON

SLEEP

Original display

No display (off)

Using sound effects

Changing the sound quality: Sound EQ

Press [SOUND EQ] repeatedly to select your desired setting.

EQ1 (HEAVY)

Adds punch to rock

EQ2 (CLEAR)

Clariﬁ es higher frequencies

EQ3 (SOFT)

For background music

EQ4 (VOCAL)

Adds gloss to vocal

EQ OFF

Cancels the EQ selection

Troubleshooting guide

Before requesting service, make the following checks. If you are in doubt about

some of the check points, or if the solutions indicated in the chart do not solve

the problem, consult your dealer for instructions.

■

Common problems

Distorted sound or no sound.

• Turn the volume up.

A "humming" sound can be heard during play.

• An AC mains lead or ﬂ uorescent light is near the unit. Keep other

appliances and cords away from the unit.

Clock display is not shown when the unit is powered by

batteries and is in standby mode.

• Connect to the household AC power in order to view the display.

"UO1" is displayed.

• Replace the batteries or use household AC power.

"F76" is displayed.

• There is a power supply problem. Consult the dealer.

■

Discs

"ERROR"

• Incorrect operation performed. Read the instructions and try again.

"NOPLAY"

• Incorrect disc format. Insert the correct disc.

Incorrect display or play will not start.

• You have not inserted the disc correctly; insert it correctly.

• Disc may be dirty. Wipe it clean.

• Replace the disc if it is scratched, warped, or non-standard.

• Condensation has formed: Wait 1 to 2 hours for it to evaporate.

■

Cassette tape

Poor sound quality.

• Clean the heads.

Recording cannot be performed.

• If the erasure prevention tabs have been removed, cover the holes

with adhesive tape.

The cassette cannot be ejected or the deck cannot be closed

when loading a cassette.

• The batteries are ﬂ at. Replace the batteries or connect to

household AC power.

• Press [4, PLAY] then [8/x, STOP/EJECT].

■

Radio

Distorted sound or noise is heard.

• Use an outdoor antenna.

A beat sound is heard.

• Turn the television off or move it away from the unit.

A low hum is heard during AM broadcast.

• Separate the antenna from other cables and cords.

Page

—