Biomorph DPF1C Manuel d'utilisation
Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Biomorph DPF1C. Biomorph DPF1C 2 pages.
Imprimer la pagebiomorph
premium ergonomic furniture
HOW TO OPERATE YOUR BIOMORPH DESK.
DPF1C control switch for Level2Plus, Maxo Series, and Flexo Series desks.
Setting Initial Height.
It may be necessary to adjust the displayed height due to different thick-
nesses of desktops, or addition of casters, etc. The DPF1C will as standard
either show 68 cm or 24.5 inch as the default desk height.
Procedure:
Press /\ and \/ keys at the same time and keep them pressed for 5 seconds.
This allows the initial height to be adjusted. Until the initial height can be
adjusted, the display will show three minuses (---) hereafter the display will
revert to showing the height. The height can then be adjusted by either /\ or
\/ until desired height has been reached. The system will return to normal
operation (and give a short blink) after 5 seconds of inactivity on the keys.
To Adjust Height in Regular Use:
= Up
V = Down
S = Store memory
• = Memory 1
•• = Memory 2
••• = Memory 3
Just push either the up or down button to adjust height and the system will
move until the button is released again or the system reaches end position.
To Set Memory:
The four small round buttons are used for memory drive/storing memory.
To store memory
• Press S – button, the display will flash for 2 seconds
• Within these two seconds press one of the small buttons with dots and
the position will be stored at this button.
• The panel will acknowledge by showing "1", "2" or "3" in the display
depending on chosen position (if panel is included)
Memory drive (small round buttons with dots)
Press one of the memory buttons and the system will start driving to the
pre-programmed memory position.
Keep the button pressed until the position is reached. Release button and
press again to go past that position.
Display function (only included on dual or multiple drive tables) shows the
actual height in either cm or inch.
Ground Support Equipment (US) ltd., DBA Biomorph, 11 Broadway, New York, NY 10004. Tel and Fax 888 302 3375 [email protected]
®
DPF1C
May or may not have digital dispplay
www.biomorph.com
Questions? Call 888 302 3375 or email [email protected]
DPF4T control switch for Plus Series Dual Drive Desks
Dual Surface Adjustment
The DPF4T switch can operate both surfaces independently.
The default setting shows the number 1 in the digital display which refers
to the near surface. By pushing the toggle button
number 2 which will then operate the rear surface. Press toggle again to
return to number 1.
Setting Initial Height.
It may be necessary to adjust the displayed height due to different thick-
nesses of desktops, or addition of casters, etc. The DPF4T will as standard
either show 68 cm or 24.5 inch as the default desk height.
Procedure:
Press /\ and \/ keys at the same time and keep them pressed for 5 seconds.
This allows the initial height to be adjusted. Until the initial height can be
adjusted, the display will show three minuses (---) hereafter the display will
revert to showing the height. The height can then be adjusted by either /\ or
\/ until desired height has been reached. The system will return to normal
operation (and give a short blink) after 5 seconds of inactivity on the keys.
Repeat for each surface.
To Adjust Height in Regular Use:
Choose near or rear surface using toggle button.
= Up
V = Down
S = Store memory
• = Memory 1
•• = Memory 2
Just push either the up or down button to adjust height and the system will
move until the button is released again or the system reaches end position.
To Set Memory:
The four small round buttons are used for memory drive/storing memory.
To store memory
• Press S – button, the display will flash for 2 seconds
• Within these two seconds press one of the small buttons with dots and the
position will be stored at this button.
• The panel will acknowledge by showing "1" or "2" in the display depend-
ing on chosen position.
Memory drive (small round buttons with dots)
Press one of the memory buttons and the system will start driving to the pre-
programmed memory position for BOTH of the surfaces.
Keep the button pressed until the both positions are reached. Release button
and press again to go past that position.
Display function shows the actual height in either cm or inch.
DPF4T
Toggle between surfaces
the display will show