BION TECHNOLOGIES cambium xl Manuel de l'utilisateur - Page 9

Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} BION TECHNOLOGIES cambium xl. BION TECHNOLOGIES cambium xl 11 pages.

Imprimer la page

S Auto reset : when enabled, any color, dimmer or speed overrides will be reset each time the scene is changed

S Trigger : sets the scene triggering mode. Time Delay and Scene Butt allow for scenes to be scrolled through without playing

Auto : the scene will be triggered as soon as it's selected

Time Delay : a short delay is added before a scene is triggered

Scene Butt. : the selected scene will not play until the scene button is pressed

First Start (F) : Default settings when the unit is first powered up

F Scene Nr. : specify a default scene number

F Scene Scene Recover : activates the previously playing scene

F Display Time : when enabled, the time will be displayed on the screen at startup

F Scene Nr. : enables the triggering of a scene at startup. If disabled, no scene will be triggered

Trigger (T) : Manages the controllers external triggering properties

T Time enable : enables the clock triggering

T Ports enable : enables the 8 dry contact ports

T RS232 enable : enables scene triggering by RS232

T IR enable : enables the infra red port (disabled by default to prevent interference)

T UDP enable : allows the controller to send and receive UDP messages required for network control

T Blackout port : enables the blackout relay output which is triggered when the stanby putton is touched

Ethernet (E) : Manages the controllers network settings

Ethernet : Enables the Ethernet socket on the controller

Dynamic IP Addr : enables dynamic IP addressing (DHCP) which allows the controller to obtain an IP address from a router

Sync Blackout: when this open is enabled, all other controllers on the network will go into standby when the standby button is

pressed

Enable NTP : enables Network Time Protocol. The controller will synchornise the clock with the internet if a connection is

evailable

NTP Server : the IP address of the server to synchronize the clock. The default is 005.135.141.108

Device's IP Add : the controllers static IP address it will use if it does not receive an IP address via DHCP

Mask: the subnet mask of the controller if not set to DHCP. Generally this is 255.255.255.0

Default Gateway : the IP address of the router if not set to DHCP

MAC Address : a unique ID used to identify the controller on the network

Date/Time (D) : Manages the date and time stored inside the controller

Date : the controllers date

Time : the controllers clock time

G Bright normal : the % brightness when the controller is not sleeping G Bright sleep: the % brightness when the controller is

sleeping

G Bright LED : the % brightness of the mode and reset LEDs

Graphics (G) : Screen management

G Image enable : allows for images to be shown for each scene if they have been assigned in the programming software

G Image full : when enabled, the image will be displayed in full screen and the scene and area will not be visible

G Image time : the time it takes before the image is displayed in full screen

G Sleep enable : when enabled, the screen brightness will dim after a certain amount of time

G Sleep time : the amount of time to wait before sleeping

G Bright normal : the brightness of the screen's backlight

G Bright sleep : the brightness of the screen's backlight whilst the controller is sleeping

G Bright LED : the brightness of the scene, undo and standby LED's

DMX Output (X) : Manage the timings of the DMX output messages and the page priorities (advanced function!)

X MBB : Mark Before Break- the time to wait between sending each 512 channel DMX message (or 'packet')

X Break : Break- the time to wait just before sending a new packet, resetting the DMX line

X MAB : Mark After Break- the message which tells your receiver to begin reading data

X MBS : Mark Between Slots- the delay time between sending each DMX channels data within the DMX packet

Univ-1/Univ-2 : each timing can be set differently depending on the universe number

X Alphab Mode : if the same scene is triggered in the global area and a second area, the area with the highest letter will take

priority

X LTP Mode : If the same scene is triggered in the global area and a second area, the latest scene triggered takes priority

Sensitive (S) : Manage the touch sensitivity settings

S USB Init : reset the touch sensitivity when the USB is connected and disconnected

S Auto Time : the time to wait before automatically resetting the touch sensitivity

S High Sense : when enabled, the sensitivity will be increased

S See Values : see each touch sensitive button number and palette value