Alpha Fan AX70-5B/40 Manuel d'instruction - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} Alpha Fan AX70-5B/40. Alpha Fan AX70-5B/40 8 pages.

Alpha Fan AX70-5B/40 Manuel d'instruction
TABLE OF CONTENT
Item
1. Safety Precautions ............................................................................... 1 - 2
2. Parts & Accessories .............................................................................. 3
3. Installation Instruction ........................................................................... 4 - 7
4. Transmitter Assembly & Function ......................................................... 8 - 9
5. Power Supply Connection & Circuit Diagram ....................................... 10 - 11
6. Maintenance ......................................................................................... 11
7. Technical Specifications ........................................................................ 12
8. Customer Service Centre ...................................................................... 13
SAFETY PRECAUTION
Warning
Installation and maintenance work shall only be performed by qualified persons, familiar with local code
and regulation, and experienced with this type of appliance.
All field wiring must be installed in accordance with the national wiring regulation.
Ensure that the rated voltage of the unit corresponds to that of the name plate before commencing wiring
work according to the wiring diagram.
The appliance must be permanently connected to the electricity supply through a double
pole switch having a contact separation of at least 3mm in all poles.
The unit must be GROUNDED to prevent possible hazard due to insulation failure.
The earth wire is approximately 60mm longer than safety wire. This is to ensure at the event whereby the
suspension system fails, the (L) and (N) wire will break leaving the fan remain earthed to prevent electro-
cution.
Tighten the blade firmly using a screw driver.
Blades that are detached from the unit during operation will cause serious injuries and property damages.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliances.
Confirm that the power supply has been switched OFF before installing or servicing the unit. Ensure that
the blade is fully static before doing any maintenance work.
STOP using the ceiling fan when any abnormality or failure occurs.
If unusual oscillating movement is observed, immediately stop using the ceiling fan and contact the
manufacturer, its service agent or suitably qualified persons.
Page No.
1
SAFETY PRECAUTION
CAUTION
Please take note of the following important points when installing.
The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with a
sufficient strength to withstand 4 times the weight of the ceiling fan.
The mounting of the suspension system shall be performed by the manufacturer, its service agent or
suitably qualified persons.
The fan is to be installed so that the blades are more than 2.5m above the floor.
Safety cord should not be longer than the earthing conductor.
Should failure of the suspension system occur, the supporting of the fan must not rely on the earthing
conductor. The earthing terminal in the fan assembly should be such that should any part of the suspen-
sion system fall off, the body of the fan assembly shall effectively earthed.
Ensure that the unit's panel is closed after service or installation.
Unsecured panels will cause the unit to operate noisily.
Sharp edges and coil surfaces are potential locations which may cause injury hazards. Avoid from
being in contact with these places.
Before turning off the power supply set the remote controller's ON/OFF switch to the "OFF"
position.
If this is not done, the unit's fans will start turning automatically when power resumes, posing a hazard to
service personnel or the user.
Do not operate any heating apparatus too close to the ceiling fan unit or use in room where mineral oil, oil
vapour or oil steam exist, this may cause plastic part to melt or deform as a result of excessive heat or
chemical reaction.
Ensure the colour of wires of the outdoor unit and the terminal markings are same to the indoors respec-
tively.
Don't use joined and twisted wires for incoming power supply.
Do not place any object in the path of the blades. Avoid raising objects or your arms near the ceiling fan.
The fan suspension system and blade screw tightening shall be examined yearly.
Replacement of parts of the safety suspension system device shall be performed by the manufacturer, its
service agent or suitably qualified persons.
Torque value for screw/bolts for securing primary suspension system for motor is 2Nm.
2