Dicon 670MBX Manuel du propriétaire

Parcourez en ligne ou téléchargez le pdf Manuel du propriétaire pour {nom_de_la_catégorie} Dicon 670MBX. Dicon 670MBX 2 pages. Mains powered smoke alarm & heat alarms
Également pour Dicon 670MBX : Manuel du propriétaire (2 pages), Manuel du propriétaire (3 pages), Manuel du propriétaire (2 pages)

Imprimer la page

M A I N S

SMOKE ALARMS

& HEAT ALARMS

COVERS • Simple Fitting Instructions • Location Guide

• User Information • Basic Fire Safety Tips

• Simple Maintenance Instructions

OWNERS

PHOTOELECTRIC SMOKE ALARMS

MANUAL

650M, 650MC, 650MRL, 650MBX

IONIZATION SMOKE ALARMS

BRK Electronics

, Dicon™

670M, 670MC, 670MRL,670MBX,

BRK Brands Europe Ltd.

HEAT ALARMS

Unit 6, Carter Court

680M, 680MC, 680MRL, 680MBX

Davy Way

Waterwells Business Park

220-240VAC (

Quedgeley

MAINS POWERED ALARMS

Gloucester

CLASS II APPARATUS

GL2 2DE

United Kingdom

IMPORTANT: PLEASE READ

AND RETAIN THIS OWNERS MANUAL

When installing this alarm for use by others, please

leave this manual or a copy with the end user.

2502-A0108-Rev A

CHECKS BEFORE USE

650MBX, 670MBX, and 680MBX:

• Check battery has been fitted correctly.

• Check alarm is not beeping.

• Test alarm before switching on the electricity supply.

All Alarms:

• Check the green light is on (behind the front grille).

• Check the red light flashes every 45 seconds or so.

• When testing linked alarms check that they all

interconnect within 10 seconds.

IMPORTANT NOTES

• Alarms with rechargeable batteries or capacitor

back up may beep for up to 2 hours while the

batteries / capacitors charge.

• Leave a copy of this handbook with the user and ensure

they know how to use and maintain the alarm.

A: GUIDANCE ON INSTALLATION

P O W E R E D

WARNING: Wiring should be installed by a qualified electrician in accordance with BS7671.

Permanent connection to the fixed wiring of the building should be made in a suitable junction box.

This alarm must not be exposed to dripping or splashing. Connect the alarm as late as possible in an

installation, particularly in new build, to avoid contamination. Remove the dust cover before applying

power.

NOTE: For detailed guidance on the siting of this alarm refer to section C of this handbook.

IMPORTANT: The circuit used to power the alarm must be a 24 hour voltage circuit that cannot be

turned off by a switch. BS5839 Part 6 states that: -

For mains powered alarms, each with an integral standby supply (Grade D), the mains electricity

supply should take the form of either:

a) an independent circuit at the dwelling's main circuit board, in which case no other electrical

equipment should be connected to this circuit (other than a dedicated monitoring device installed to

indicate failure of the mains electricity supply to the alarms); or

MODELS:

b) a separately electrically protected, regularly used local lighting circuit.

For mains powered alarms, with no standby supply (Grade E), the mains electricity supply may only

take the form of an independent circuit as per a) above. If it is necessary to use an RCD for protection,

it should operate independently of any RCD protection for circuits supplying sockets or portable

equipment.

All interconnected alarms should be installed on a single final circuit.

NOTE: The maximum interconnect wiring length is 250 metres. The maximum number of alarms

interconnected together is 12. BRK Dicon smoke alarms should not be connected to any model

produced by another manufacturer.

The location of the alarms must comply with the applicable building codes and the advice in section C:

)

WHERE TO LOCATE below.

B: INSTALLATION (See Diagrams 1 & 2)

1. Use either of the methods of installation

shown in diagrams1 and 2.

When selecting cable for connecting

interlinked smoke alarms the interlink wire

should be treated as live.

The installation method shown in diagram

1 is suitable for a plasterboard or similar

ceiling where access to the void behind it

is available and suitable to mount the

junction box.

The installation method shown in diagram

2 is suitable for concrete or similar

ceilings where access is insufficient or

where surface wiring is necessary.

2. Connect the brown wire to the brown (live)

in the house wiring and the blue wire to the

blue (neutral). NO CONNECTION SHOULD

BE MADE TO THE MAINS ELECTRICITY

SUPPLY EARTH TERMINAL. TERMINATE

HOUSE WIRING EARTH

IN SPARE CONNECTOR.

3. For multiple alarm installations use a "three

core and earth" style cable between all the

alarms to be interconnected and connect the third core of that cable to the white wire from the

smoke alarm. DO NOT use the earth wire for the interconnect line. This must be treated as live,

i.e. insulated and sheathed. If the alarm is not going to be interconnected, cap the unused

wires.

4. Remove the baseplate from the back of the alarm by twisting anti-clockwise as far as it will go.

(about 12 mm). Detach the locking pin.

650MBX, 670MBX and 680MBX

Detach battery door screw from the base plate. Open the battery door on the back of the

alarm, connect the battery, close the door and secure with the screw provided before fitting

the alarm to the baseplate.

Test the alarm using the test button.

5. Attach the flat side of the mounting plate and tighten screws to fit snugly against the pattress

or junction box and ceiling or wall.

6. Bring the power connector through the centre opening of the plate.

IMPORTANT: THE PAPER GASKET SUPPLIED

MUST BE FITTED BETWEEN THE REAR OF THE

ALARM AND THE MOUNTING PLATE TO PREVENT

THE ALARM FROM BECOMING CONTAMINATED

BY DUST AND TO ENSURE THE CORRECT

OPERATION OF THE ALARM. Gasket not required

on alarms fitted with protective film on the back.

7. Plug the lead into the rear of the alarm.

8. Place the alarm on the baseplate by lining up

arrows on the baseplate and the alarm rim and

twist clockwise to fasten.

To secure the alarm to the baseplate, insert the

locking pin (removed from the base in 5

above) into the 'T' shaped slot located above

the arrow on the rim of the alarm.

Fit either locking key into the 'Key Slot' above

the battery drawer handle. Key number 1 locks

the alarm to the base, key number 2 locks the

alarm to the baseplate AND the battery drawer

closed. These keys remain in place and should

only be removed when opening the battery

drawer or removing the alarm from the

baseplate.

LOCKING PINS / KEYS MUST BE FITTED. DO

NOT ATTEMPT TO REMOVE THE ALARM

FROM THE BASEPLATE WITHOUT FIRST

REMOVING THEM.

BROWN (LIVE)

9. Switch on the mains electricity supply.

BLUE (NEUTRAL)

10. Check that the green light is on and that the red light is flashing every 45 seconds or so.

BLACK or GREY (INTERLINK)

The lights are located behind the grille on the front of the alarm.

EARTH

11. Press and hold the test button until the alarm sounds. NOTE: On the 670 series, pressing this

button places the alarm in pause mode.

SYSTEMS OF MORE THAN ONE ALARM

JUNCTION BOX

Test each alarm in the system checking that all other alarms in the system are triggered within 10

seconds.

WARNING

BASEPLATE

BROWN

Do not attempt to test the alarm with flame heat or smoke, the results may be misleading and may

WHITE

BLUE

damage the alarm.

The dust cover must be removed as late as possible before commissioning. This will reduce the

Diagram 1

ALARM

chances of the alarm being contaminated by building dust etc.

Remove the alarm from the system before testing the wiring with high voltage insulation testing

equipment otherwise this will damage the alarm and will invalidate the warranty.

BATTERY

ACCESS

DOOR

C: WHERE TO LOCATE

1. As a minimum smoke alarms should be located between sleeping areas and potential sources of

fire such as living rooms and kitchens. In single storey homes with one sleeping area a smoke

INSTALLATION USING JUNCTION BOX

alarm should be installed in the hallway as close as possible to the living accommodation. To

ensure audibility in the bedrooms it may be necessary to install more than one smoke alarm,

particularly if the hallway is more than 15m long. In single storey homes with two separate

sleeping areas, a minimum of two smoke alarms is required, one outside each sleeping area. In

multilevel or split level homes as a minimum a smoke alarm should be installed on the ground floor

between the staircase and any rooms in which a fire might start and on each storey in circulation

areas which form part of the escape route (normally hallways and landings).

NOTE: Heat alarms should not be used in escape routes instead of smoke alarms. They should

only be used in the applications listed below in addition to smoke alarms and should always be

interconnected to smoke alarms.

2. Additional alarms should be installed in bedrooms in anticipation of fires originating there, caused

by faulty wiring, lights, appliances, smokers or other hazards.

3. For best protection, smoke alarms should be installed in every room in your home, apart from

those listed in the 'LOCATIONS TO AVOID' section. Heat alarms should be used in kitchens, boiler

rooms, laundry rooms, garages and such like where smoke alarms would be unsuitable. All alarms

must be interconnected.

Diagram 2