Olympus CAMEDIA C-3040 Zoom Manuel de démarrage rapide - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel de démarrage rapide pour {nom_de_la_catégorie} Olympus CAMEDIA C-3040 Zoom. Olympus CAMEDIA C-3040 Zoom 2 pages. External flash or strobes not firing with olympus cameras
Également pour Olympus CAMEDIA C-3040 Zoom : Dépannage (3 pages)

Olympus CAMEDIA C-3040 Zoom Manuel de démarrage rapide
http://www.olympus.com
2.
Shooting
Taking Pictures
1. Remove the Lens cap and set the Mode
dial to "P" (Program mode).
2. Point the camera at your subject.
Look through the viewfinder and point
the camera at the person or object you
want to photograph (the subject).
Position the AF target mark over the subject.
You can also look at the image on the Monitor to
take pictures.
Press the
(Monitor) button to switch the
Monitor on and off.
[To zoom in]
By turning the zoom lever to "T", you can enlarge the picture of your subject. When you
turn the zoom lever towards "W", the image reverts to the size it was when you switched
the camera on, allowing you to shoot a wider area.
3. Focus on your subject. (Press the shutter
button down halfway.)
With the camera pointed at your subject,
press the shutter button down lightly.
The camera gives 2 short beeps and the green
lamp lights. At this point, the focus and exposure
(shutter speed and aperture setting) are locked.
If the green lamp blinks, this indicates that the
camera cannot focus. Release the shutter button,
move the position of the AF target mark slightly
and then lightly press the shutter button again.
4. Take the picture. (Press the shutter
button down fully.)
With the shutter button pressed down
halfway, press it down further so it is
fully depressed. The camera gives a
short beep and takes the picture.
The camera then starts recording the image onto
the card and the card access lamp blinks.
If the green lamp light up when you press the shutter
button, you can take another picture, even if an image
is being recorded onto the SmartMedia card. If you
are taking a picture in low-light conditions, the
flash will fire automatically.
When your subject is not in the center of the shot (focus lock)
First, position the AF target mark over your subject and press the shutter button halfway
to focus the camera. Then hold the shutter button down as you move the camera to com-
pose the shot as you want it and, without releasing the shutter button, press the shutter
button down fully to take the shot.
C-3040ZOOM
Quick Start Guide
Flash mode
Macro mode
Spot metering mode
P
Sequence mode
Self-timer/
Remote control
Available functions from button on C-3040ZOOM
Viewfinder
Flash Mode Button
The flash mode changes each time you press this button. The available flash modes are
AF target mark
"Auto-Flash", in which the flash fires automatically in low-light and backlit conditions, "Red-
Eye Reduction Flash" (
appear red), "Forced Flash" (
conditions, and "Flash Off" (
Spot/Macro Button
The light metering mode or Macro mode changes each time you press the Spot/Macro button.
The available modes are "Normal", which is used for normal autofocus photography,
"Spot Metering mode" (
useful for shots such as dark subjects in backlit shots, "Macro mode"(
you to focus on subjects 7.9" to 31.5" from the camera, and "Macro + Spot Metering
Half pressed
Fully pressed
mode" (
), which measures light only at the center of a close-up subject.
Shooting Movies
1. Set the Mode dial to
AF target mark
The Monitor switches on and displays the available shooting time.
Green ramp
2. Shoot in the same way as for "P" mode.
The camera starts shooting when you press the shutter button
down. Press the shutter button again to end shooting.
The lowest memory gauge lights, the card access lamp blinks
and the camera starts recording the movie onto the card. You
can continue shooting when the lamp stops blinking and the
camera finishes recording data onto the card.
3.
Viewing Your Shots
Set the Mode dial to
* The most recent shot is displayed on the Monitor
(Single-frame playback).
• Use the Arrow pad to select the image you want to view.
: Displays the previous shot.
Card access lamp
: Displays the next shot.
: Jumps back 10 shots.
: Jumps forward 10 shots.
* To display multiple shots (Index playback), turn the zoom lever to "W".
* To display a shot enlarged (in close up), turn the zoom lever to "T".
Manual focus
Slow synchro
Flash intensity control
Battery check
Card error
White balance
ISO indicator
Exposure compensation
Auto bracket
Recording mode
Number of storable pictures
Card writing
Sound record
), which reduces the "red-eye" effect (where the subject's eyes
), in which the flash fires for every shot regardless of the
), in which the flash never fires, even in low-light conditions.
), which measures light only at the center of the shot and is
), which allows
.
F2.0 1/800 +2.0
Memory
AF target mark
gauge
.
12.23. , 00 21:56
Arrow pad
1234
1235
1237
1238
1240
1241
OLYMPUS AMERICA INC.
Two Corporate Center Drive, Melville, NY 11747-3157, U.S.A. Tel. 631-844-5000
(Customer support) Tel. 1-888-553-4448
You can display images marked with the
icon as movies. Press the
use the Arrow pad to select "MOVIE PLAY" and then press
the [OK] button. When the card access lamp stops blinking, the movie starts playing. When
the movie ends, press the
(Menu) button to display the menu and then press the Menu
button again to exit Movie playback mode.
• When a movie is running, you can use the Arrow pad to do the following:
: Jump to the start of the current movie.
: Jump to the end of the current movie.
: Play the movie for as long as the button is held down.
: Play the movie in reverse for as long as the button is
held down.
[OK] button: Pause the movie.
Press this button again after the movie has finished to play the movie again.
4.
Erasing Pictures
You can erase pictures you no longer need by erasing them one at a time
(one-frame erase) or by erasing all the images on the card (all-frame erase).
Use the steps in "3. Viewing Your Shots" to display the image you want to erase.
One-frame Erase
Press the Erase button on the camera, use the
Arrow pad to select "YES" and then press the [OK]
button.
All-frame Erase
Press the
(Menu) button and use the Arrow pad to select "CARD SETUP" and
then press
. Press
or
to select "
Select "YES" in the confirmation screen and then press the [OK] button again.
(To cancel image erasing, select "NO" and press the [OK] button.)
CARD
SETUP
MODE
SETUP
[
2 / 2
]
This screen shows the still
picture playback menu.
Switch the camera off when you've
5.
HQ
finished shooting.
Always switch the camera off when you have finished taking pictures.
Check that the card access lamp is no longer blinking and then set the
6453
Mode dial to "OFF".
• The Monitor and control panel go blank.
1236
• If you leave the camera switched on without using it in any way for 3 minuts or longer, the
Monitor and control panel automatically go blank to conserve battery power. (This is
1239
referred to as Sleep mode.) To revive the camera when it is in Sleep mode, simply press any
of the camera's controls.
1242
• Always fit the lens cap when you put the camera away.
(Menu) button and
. When "START" appears, press
MOVIE
START
PLAY
INFO
FUNCTION
CARD
SETUP
MODE
SETUP
[
1 / 1
]
YES
NO
OK
YES
NO
" and then press the [OK] button.
YES
NO
YES
OK
NO
Confirmation screen