Olympus Stylus 820 Manuel d'instruction - Page 4

Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} Olympus Stylus 820. Olympus Stylus 820 5 pages. Ikelite digital camera housing

Imprimer la page

O O p p t t i i o o n n a a l l A A c c c c e e s s s s o o r r i i e e s s C C o o n n t t i i n n u u e e d d

AF35 Autoflash kit

includes :

- AF35 strobe

- Flex arm

- AutoFlash sensor

- Handle with rubber grip

- Tray (single or dual)

- Mounting hardware

The Autoflash AF35 replicates your

camera's flash for automatic exposure in

any situation. Single or dual trays can

attach directly to your housing. The

exposure selector dial on the side of the

sensor provides fine tuning to optimize

results with a variety of digital still

cameras. Once you find an exposure level

that you like, leave the dial on that

number for automatic operation.

C C o o m m p p l l e e t t e e i i n n f f o o r r m m a a t t i i o o n n r r e e g g a a r r d d i i n n g g o o p p t t i i o o n n a a l l a a c c c c e e s s s s o o r r i i e e s s a a v v a a i i l l a a b b l l e e a a t t

w w w w w w . . i i k k e e l l i i t t e e . . c c o o m m

C C o o n n t t r r o o l l M M a a i i n n t t e e n n a a n n c c e e

Ikelite controls are designed to provide years of reliable service

with minimal maintenance.

1 . Push button controls require no maintenance other than rinsing

in fresh water after saltwater use. If a push button control

becomes difficult to push or if it sticks when depressed, soak the

housing in luke warm fresh water. After a few minutes operate

the push button. If this does not correct the problem, return the

housing to Ikelite for maintenance.

housing

2. Some of the controls have long shafts. These controls can be

pulled out, exposing the shaft (see drawing).

To lubricate the control, gently pull on the knob until the

stainless steel shaft is exposed. Lightly lubricate the shaft, then

move the shaft in and out several times. This will lubricate the

x-ring in the Ikelite control gland. This should be done before

using the housing after a prolonged storage period, or once a

week when the housing is in use.

lubricate shaft

pull out to

expose shaft

M M a a i i n n t t e e n n a a n n c c e e

The Ikelite Digital Housing should be given the same care and

attention as your other photographic equipment. In addition to

normal maintenance we recommend that the housing be returned

to Ikelite periodically to be checked and pressure tested.

1 . D D o o N N o o t t leave the camera and housing in direct sunlight for

prolonged periods. Heat may damage the camera.

2. D D o o N N o o t t ship the camera in the housing.

3. Before using the housing, always check the tightness of the s s e e t t

s s c c r r e e w w in each control knob.

Check each c c o o n n t t r r o o l l g g l l a a n n d d penetrating the housing to make sure

they are tight. There is a slight chance that either could vibrate

loose during travel.

4. Keep the back o-ring clean and lightly lubricated. To lubricate

remove the o-ring from the back. Put a small amount of lkelite

lubricant on your fingers. Draw the o-ring through your fingers

to apply a light coating of lubricant. Only apply enough

lubricant to make the o-ring feel slick. D D o o N N o o t t s s t t r r e e t t c c h h t t h h e e

o o - - r r i i n n g g . This light coating of lubricant will help to keep the

o-ring from drying out and will help to show a dark sealing

line when the housing back is properly sealed.

5. Keep the area where the o-ring fits and the sealing surface of

the housing clean.

6. Rinse the housing exterior thoroughly in fresh water after each

salt water use. Dry with a soft cloth. Dry lens port to eliminate

water spotting.

After several uses in salt water soak the housing exterior in a

mild soap solution, rinse and dry before storage. When storing

the housing, remove the back o-ring, lightly lubricate and place

in a plastic bag. Place the plastic bag with o-ring inside the

housing for safe keeping.

C C o o n n t t r r o o l l M M a a i i n n t t e e n n a a n n c c e e C C o o n n t t . .

3. Some of the controls have a short shaft and cannot be pulled

out exposing the shaft for lubrication. In the unlikely event one

of these controls sticks or becomes difficult to operate you can

remove the control from the housing and lubricate it, or return

the housing to Ikelite for maintenance. To remove the control,

loosen the set screw in the knob (allen wrench required);

remove the knob. If there is salt or dirt build-up on the exposed

control shaft, clean the shaft. Open the housing and gently slide

the control shaft out of the control gland. Clean and lightly

lubricate the shaft, including the end of the shaft. Slide the

shaft back into the control gland and gently slide it back and

forth a few times without fully removing the shaft from the

gland. Replace the knob, NOTE the flat area on the shaft, the

set screw in the knob should tighten down against the flat area

on the control so the knob does not turn on the shaft.

housing

control

shaft

Flat

Tighten set screw down

against this area when

replacing the knob.

Lubricate end of shaft

before reinserting into

gland

Loosen set screw

(allen wrench required)