Olympus BH2 Series Démontage, nettoyage et remontage complets - Page 4
Parcourez en ligne ou téléchargez le pdf Démontage, nettoyage et remontage complets pour {nom_de_la_catégorie} Olympus BH2 Series. Olympus BH2 Series 23 pages. Phase contrast
Également pour Olympus BH2 Series : Manuel de dépannage et de réglage (46 pages), Démontage, nettoyage et remontage complets (40 pages), Démontage, nettoyage et remontage (45 pages), Manuel (6 pages), Manuel d'installation (9 pages)
Table of Figures
Figure 1 - Head of a typical JIS screw ..................................................................................................................................... 6
Figure 2 - Protect the top of the arm from dust .................................................................................................................... 7
Figure 3 - Remove the lamphouse from the base . ................................................................................................................. 8
Figure 4 - Bottom view of the BHT/BHTU electrical base ...................................................................................................... 8
Figure 5 - Light pre-set control and pre-set switch ................................................................................................................ 8
Figure 6 - Remove screws securing the arm to the base ....................................................................................................... 8
Figure 7 - Separate the arm from the base ............................................................................................................................ 8
Figure 8 - Remove screws securing the trim cover ................................................................................................................ 9
Figure 9 - Remove the loose trim cover from the arm . .......................................................................................................... 9
Figure 10 - Loosen screws securing guide block in place ....................................................................................................... 9
Figure 11 - Loosen screws tensioning slide mechanism ........................................................................................................ 9
Figure 12 - Withdraw focus block assembly from the arm .................................................................................................... 9
Figure 13 - Remove screws securing the guide block .......................................................................................................... 10
Figure 14 - Remove the guide block from the focus block . .................................................................................................. 10
Figure 15 - The components of the focus block assembly ................................................................................................... 10
Figure 16 - Remove the brass shims from the focus block .................................................................................................. 10
Figure 17 - Remove screws and wedge nuts . ....................................................................................................................... 10
Figure 18 - Remove four guide rails from the arm casting . .................................................................................................. 10
Figure 19 - Clean grease from the guide rails ...................................................................................................................... 11
Figure 20 - Clean grease from the side grooves in the arm ................................................................................................. 11
Figure 21 - Remove screws securing bottom dust cover ..................................................................................................... 11
Figure 22 - Remove the bottom dust cover ......................................................................................................................... 11
Figure 23 - Remove two guide rails from the focus block . ................................................................................................... 11
Figure 24 - Clean grease from side groove in focus block . ................................................................................................... 12
Figure 25 - Remove guide rails from the guide block . .......................................................................................................... 12
Figure 26 - Clean grease from side groove in guide block ................................................................................................... 12
Figure 27 - Soak the rollers in solvent to remove grease . .................................................................................................... 12
Figure 28 - Reinstall the long guide rails into the arm ......................................................................................................... 12
Figure 29 - Scrub grease from guide rails and arm .............................................................................................................. 12
Figure 30 - Guide rails installed into the arm casting . .......................................................................................................... 13
Figure 31 - Reinstall short guide rails into the focus block .................................................................................................. 13
Figure 32 - Scrub grease from guide rails and focus block . .................................................................................................. 13
Figure 33 - Guide rails installed into the focus block ........................................................................................................... 13
Figure 34 - Reinstall short guide rails into the guide block .................................................................................................. 13
Figure 35 - Scrub grease from guide rails and guide block .................................................................................................. 13
Figure 36 - Guide rails installed into the guide block . .......................................................................................................... 14
Figure 37 - Reinstall the brass shims onto the focus block .................................................................................................. 14
Figure 38 - Clean exposed grease from the focus block ...................................................................................................... 14
Figure 39 - Reinstall guide block onto the focus block . ........................................................................................................ 14
Figure 40 - Loosely engage screws with the wedge nuts . .................................................................................................... 14
Figure 41 - Place rollers and rod onto bottom guide rails ................................................................................................... 15
Figure 42 - Place focus block assembly onto rollers ............................................................................................................ 15
Figure 43 - Withdraw the guide block about halfway . ......................................................................................................... 15
Figure 44 - Place four rollers on the upper guide rails . ........................................................................................................ 15
Figure 45 - Push cylindrical rollers into guide-rail channel .................................................................................................. 15
Figure 46 - Push the spacer rod into guide-rail channel ...................................................................................................... 16
Complete Teardown, Cleaning, and Reassembly of the Olympus BH-2 Sliding Focus Block
Revision 2
Page 4 of 23