AccuLite Areos Instructions d'installation

Parcourez en ligne ou téléchargez le pdf Instructions d'installation pour {nom_de_la_catégorie} AccuLite Areos. AccuLite Areos 2 pages. Led

Imprimer la page

Important Safeguards:

WARNING – When using electrical equipment, basic safety precautions should always be used including the following:

This product must be installed in accordance with the applicable installation code by a person familiar with the construction

and operation of the product and the hazards involved.

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

❶

Disconnect Power

• Disconnect Power during installation and maintenance.

❷

Prepare Luminaire for Mounting

• Open the wiring compartment by removing the two screws (A1) (see Figure 1)

❸

Install Bolster Plate

• Using the nut and long bolt (1) attach the bolster plate to the pole as illustrated

❹

Secure Wiring

• Insert wires through wireway

• Tether the wires using the cable tie

Important Safeguards:

❺

Mount the Luminaire

Important Safeguards:

• Hang luminaire on bolt

WARNING – When using electrical equipment, basic safety precautions should alwats be used including the following:

• Secure bolt

➀

finger tight

This product must be installed in accordance with the applicable installation code by a person familiar with the construction

• Align the bolster plate and attach the short bolt

This product must be installed in accordance with the applicable installation code by a person familiar with the construction

and operation of the product and the hazards involved.

• Tighten bolts

➀

and

➂

and operation of the product and the hazards involved.

❻

Check Voltage

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

• Connect leads to proper voltage

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

• Attach the appropriate leads to the terminal block mounted on the wiring

Mark means lamp contains mercury.

compartment door (A4) (See figure 1)

Mark means lamp contains mercury.

Follow disposal laws.

• Individually cap all unused leads.

Follow disposal laws.

See www.lamprecycle.org

• Close the wiring compartment

See www.lamprecycle.org

Aiming the Optics

Disconnect Power

• Disconnect Power during installation and maintenance.

Unless pre-aimed at the factory (options RL or RR), standard fixtures are shipped

• Disconnect Power during installation and maintenance.

with optics aimed to the front. If a different orientation is needed, the optics can

Prepare Luminaire for Mounting

be field rotated 90 degrees to the right or to the left. To rotate the optics, follow

• Open door assembly.

these steps:

• Remove protective plastic from the reﬂector sides

• Disconnect Safety Cable from door assembly.

❶

• Disconnect Safety Cable from door assembly.

Loosen the screws (A2) securing the Driver Housing Cover (A3) (see Figure 1)

• Swivel door assembly to

and remove cover

• Swivel door assembly to

• For ease of installation, the tray mounted ballast may also be removed. Hold

❷

• For ease of installation, the tray mounted ballast may also be removed. Hold

tray with one hand while loosening the thumb screw and let hang. Move past

Loosen the 4 bolts (A5) securing the LED Housing to the Driver Housing.

tray with one hand while loosening the thumb screw and let hang. Move past

90˚ to remove.

After all 4 bolts are removed the LED housing will drop about ¼" allowing

90˚ to remove.

Install Bolster Plate

for rotation.

Install Bolster Plate

❸

• Using the nut and long (2-1/4") bolt

Rotate 90 degrees in any direction

• Using the nut and long (2-1/4") bolt

❹

Secure Wiring

Insert back all 4 bolts (A5) to secure the LED Housing to the Driver Housing

Secure Wiring

• Insert cable through wireway

and tighten.

• Insert cable through wireway

❺

• Tether the cable using the cable tie

Close the Driver Housing Cover (A3)

• Tether the cable using the cable tie

Mount the Luminaire

• Hang luminaire on bolt

• Secure bolt

ﬁnger tight

• Secure bolt

ﬁnger tight

• Align the bolster plate and attach the short (1-3/4") bolt

• Tighten bolts

and

• Tighten bolts

and

Check Voltage

• Luminaires with multi-tap ballasts are factory wired to the highest voltage.

For other voltages, ensure correct leads are used.

• Connect leads to proper voltage.

• Attach the appropriate leads using approved connectors.

• Individually cap all unused leads.

Orient Optics

• If optical assembly is not

oriented correctly, remove by

Technical Support: 888 / 387-2212

oriented correctly, remove by

loosening four screws to and

rotate as illustrated

loosening four screws to and

Figure 2 & 3

➁

mounted on the bolster plate.

Note the position of the two washers

➀

➂

approximately 50˚ and remove.

Figure 1 & 2

, attach the bolster plate as illustrated.

mounted on the bolster plate.

Note the position of the two washers

Areos

LED

™

Installation Instructions

Figure 1

Cover

Bolts

Figure 2

Figure 3

Figure 2

Polycarbonate Guard

• Remove door assembly

• Locate the four dimples in

SAVE THESE INSTRUCTIONS

• Assemble and attach the

Screws

Figure 2

Figure 1

Pole

Figure 1

Pole

Drilling

Pattern

Luminaire

Flat washer

Lock washer

Flat washer

Lock washer

2-1/4" Bolt

Flat washer

Lock washer

Flat washer

Lock washer

1-3/4" Bolt

from the luminaire

the corners of the door and

drill clearance holes for a

the corners of the door and

#6 screw.

drill clearance holes for a

#6 screw.

polycarbonate guard as

illustrated.

polycarbonate guard as

illustrated.

P3330

Rev 1/16

Screws

Z-12108

Rev 5

1-1-08

Rev 5

1-1-08

Wiring Cover

Ø 7/16"

(x2)

Ø 7/16"

(x2)

MIN

Ø 1"

1-1/2"

Ø 1"

1-1/2"

Pole

Bolster Plate

(This end is

Bolster Plate

unthreaded)

(This end is

unthreaded)

Nut

Lock washer

Cable Tie

Bolster Plate

(This end is

Bolster Plate

threaded)

(This end is

threaded)

Drill

here

Drill

here

Nut

Lock Washer

Nut

Lock Washer

Door

Spacer

Flat Washer

Polycarbonate Guard

Flat Washer

Polycarbonate Guard

Screw

Flat Washer

Screw