Axon Flex 2 Manuel de démarrage rapide
Parcourez en ligne ou téléchargez le pdf Manuel de démarrage rapide pour {nom_de_la_catégorie} Axon Flex 2. Axon Flex 2 2 pages.
Imprimer la page
Axon Flex 2 Quick Start Guide
English
Camera cable
Axon Flex 2 camera
Read, understand, and follow all current instructions, warnings, and relevant Axon training materials before using any Axon system. The
most up-to-date warnings and instructions are available at www.axon.com.
Before using an Axon Flex 2 system, ensure it is fully charged, and connect it to Evidence.com via the Axon Dock or Evidence Sync software to
ensure it is properly configured. See Controller Battery LED and Recharging the Battery and Uploading Data for more information. If the battery's
charge is ever depleted, recharge and reconnect the connect the system again.
Recording
The Axon Flex 2 system has 2 operating modes. The default mode, or
BUFFERING mode, provides pre-event buffering to capture activities that
occur before you activate the EVENT (recording) mode.
1
Turn the system on. Move the ON/OFF switch to the ON position.
• The camera takes a few seconds to boot up and be ready to record
(the red area under the switch will be exposed with the switch moved
to the ON position).
• The operation LED will be solid red and then transition to blinking
green when the system goes into BUFFERING mode.
• The system will go into BUFFERING mode after the boot up sequence.
With default settings, the BUFFERING mode holds the previous
30 seconds of video (NO AUDIO) leading up to the beginning of a
recording.
Controller Operation LED
The controller's operation LED displays the system's current operating
mode.
Operating Mode
EVENT
BUFFERING
Recovering interrupted video*
Booting up/powering down
Error state**
Cable disconnect
* When the function LED also is blinking red. If little video was interrupted,
the function LED will blink only briefly.
** When the Function LED also is solid red.
Controller Function LED
The Axon Flex 2 controller's function LED displays when certain functions
are enabled.
Hardware
Axon Flex 2 controller
Also available:
USB C to A Sync cable
Blinking green
Solid red
BUFFERING mode
Boot up mode
Controller LED
Blinking red
Blinking green
Blinking red
Solid red
Solid red
Blinking yellow
Quick Reference
Cable Connection Port
Function LED
Also for data transfer and
recharge with PC or Axon
Dock
Slide Lock
Holds cable to controller
Battery LED
Green = 40–100%
Yellow = 20–39%
Red = Less than 20%
Status LED
(bottom of controller)
2
To record, quickly double-press the EVENT button.
• The system now records audio as well as video.
• The system will beep twice to let you know that recording started.
The 2 beeps will repeat every 2 minutes (if the system is muted, there
will be no audio notifications).
• The operation LED will blink red.
3
To stop recording and return to BUFFERING mode, press and hold the
EVENT button for at least 3 seconds until there is a long, audible beep.
EVENT button
Because the system does not capture audio in BUFFERING mode, the
first 30 seconds of a recorded event will be video-only (depending
on your agency's settings). BUFFERING mode starts only after the
camera boots up. The system does not record when the Axon Flex 2
controller is turned off.
Controller Battery LED
The controller's battery LED displays the battery's remaining capacity,
when the device is being used or when charging.
Battery Capacity
Battery capacity is 40–100
percent
Battery capacity is 20–39 percent
Battery capacity is less than 20
percent
Function Enabled
Mute
Camera error***
Pairing mode
*** Use the power switch to turn the camera off and on.
Microphone
Speaker
Operation LED
Power Switch
Red = On/Buffering
Speaker
Function Button
Mute or add marker
EVENT Button
Double-press = Start record
Hold 3 seconds = Stop record
Battery Status Button
Push to show status of battery
Blinking red – recording mode
Battery LED
Green
Yellow
Red
Function LED
Blinking blue
Solid red
Blinking green