Epson ActionLaser II Informations sur le produit - Page 7

Parcourez en ligne ou téléchargez le pdf Informations sur le produit pour {nom_de_la_catégorie} Epson ActionLaser II. Epson ActionLaser II 12 pages. Epson actionlaser actionlaser ii: product information
Également pour Epson ActionLaser II : Bulletin d'information sur les produits (2 pages)

Imprimer la page

Paper Handling Options

The Multi-Media Feeder
The optional multi-media feeder handles automatic feeding of many
types of paper. It holds up to 150
paper from 98 to 216 mm (3.86 to 8.50 inches) wide and from 148 to
356 mm (5.83 to 14.0 inches) long. You can load two different sizes of
paper in your printer at once (one size in
the
other in your standard paper cassette). You can also set SelecType
Level 1 INPUT to AUTO and use both the multi-media feeder and
the standard paper cassette for continuous printing of up to 250
sheets of the same size paper.
Installing the multi-media feeder
1. Remove the manual feed paper guide.
2. Attach the multi-media feeder as shown below. Then, mount the
multi-media feeder safely on the printer.

Status and Error Messages

If an error occurs, your best source of information is the display
the control panel. The messages displayed there tell
and, in some cases, indicate the actions you should take to
wrong
correct the problem. Status messages appear on the display during
normal operation. They indicate
This section contains
alphabetical list of status and error messages
an
you may encounter while printing and includes steps you can take to
correct
any
problems.
Laser Printers
of paper, and it can feed
sheets
the
multi-media feeder and
you what may be
the
printer's current status.
Note:
some
In
cases, the
detected. This requires you to correct
to clear the error. However, if the AUTO CONT option in
CONTINUE
SelecType is set to on, some errors may clear automatically even
problem remains. In most instances, you should leave
though the
AUTO CONT set to off.
The messages
In this
section, status messages are preceded by [S], error messages
are preceded by [E] and warning messages are preceded by [W]. In
some cases the message you see on your display also shows the
printer mode.
[E] ADD MEMORY FOR U-I-X
This indicates that there is not enough memory in Channel X. See
Chapter 4 for instructions on changing the RX-BUFFER SIZE or
adjusting the memory distribution in the INDIVIDUAL setting or
see Appendix A for adding memory.
[E] CANCEL MANUAL FEED
This message indicates that there is no paper in the manual feed
slot when you are using manual feed. See Chapter 5.
[E] CHANGE PCU XXXXX
Replace the photoconductor unit as described in Chapter 6.
The PCU counter tells you the number of pages that have been
printed.
[S] CHAR CREATING
Characters are being created.
[S] COPY END
Multiple-copy printing is cancelled. (You pressed the
button when the printer was off line.)
[E] COVER OPEN
The printer or fan cover is open or the toner cartridge or
photoconductor unit is not installed. Close the printer or fan
cover or install the toner cartridge and photoconductor units.
[S] DATA
The printer has received data but is not yet printing or
has received data and is off line. If the printer is off line, press
FEED
to print the data.
[E] FEED JAM
Paper is not feeding into the printer from the specified cassette or
has jammed on its way into the printer. See the FEED JAM section
in this chapter for information.
[S] FONT CREATING
A font is being created.
[S] GRAPHIC DRAWING
Graphics are being drawn.
[E] ILLEGAL CARD
A card in the card slot or a cartridge in
be read. To correct this error, take the printer off line and then
press
CONTINUE.
printer is off line and remove the card or
on
CONTINUE
light still flashes, press
[S] INITIALIZE
The printer is being initialized to the factory or optional settings.
9/17/91
ActionLaser II
red
CONTINUE light flashes when an
the
problem and then press
cartridge slot cannot
the
If the error
message
remains, make sure the
cartridge. If
the
CONTINUE.
error is
COPY END
the
printer
red
the
ALll-7