Architectural Mailboxes 6900 E Instructions de montage
Parcourez en ligne ou téléchargez le pdf Instructions de montage pour {nom_de_la_catégorie} Architectural Mailboxes 6900 E. Architectural Mailboxes 6900 E 2 pages. Parcel drop
Imprimer la page
elephantrunk
parcel drop
Carefully unpack the elephantrunk, parts and hardware.
Hardware and Parts (included)
x 1, mounting bolt
x 1, lag shield
(for hardscape
installation only)
x 1, handle
x 4, leveling feet
This address is equipped with an
elephantrunk
parcel drop
TM
location:
x 2, keys
www.architecturalmailboxes.com
©
Architectural Mailboxes, LLC, 2012. Rev I
x 1, placard
x 1, cushion
x 1, outgoing partition
Choose where to locate your elephantrunk
NOTE: The elephantrunk parcel drop is NOT intended to replace a mailbox. Its primary
purpose is to receive parcel deliveries.
The courier must be able to freely access your elephantrunk to make deliveries.
Choose a protective location, such as on a porch or under an eave, and away from sprinklers.
You can anchor your elephantrunk to a hardscaped or wooden surface. It will require drilling a hole into the surface, so make sure you
pick the right location.
elephantrunk installation
1
Place your elephantrunk at the desired location with
the help of another person.
2
Open the bottom
door and mark the
ground through the
hole in the floor.
After marking the ground, place the elephantrunk
3
aside before continuing.
TM
by
R
Tools (not included)
x 1, washer
Drill suitable for drilling into masonry or wood
x 2, handle screws
Hex wrench
x 4, placard screws
- or -
Phillips head screwdriver
x 1, mounting knob
5/8" masonry drill bit
(if installing on hardscape)
1/4" wood drill bit
(if installing on wood deck/porch)
4
Drill a hole where you marked the ground:
For hardscape (for example, stone walkway or
concrete pad), drill a hole 2.5" deep at the mark with
a 5/8" masonry bit.
For wood (for example, deck or porch), drill a pilot
hole 2" deep at the mark using a 1/4" wood bit.
5/8" hole
5
For hardscape:
Remove any debris
from the hole and insert
the lag shield so it is
flush with the surface.
Screw the mounting bolt
into the lag shield.
Use the hex portion at the
center of the bolt to screw
it into the hole.
For both installations,
screw it all the way so the
hex portion is touching
the surface.
6
Carefully screw the four
leveling feet into the bottom
of each leg about half way.
elephantrunk use
1/4" hole
[email protected] with any questions.
For wood:
7
With help, lift the elephantrunk over the installed bolt,
Screw the
aligning the bolt through the hole in the floor. DO NOT
mounting bolt
secure in place with the mounting knob yet.
directly into the
8
Level the elephantrunk by adjusting the feet up
surface.
and down.
9
Place the washer over the bolt and screw on the
mounting knob. The knob only needs to be hand
tightened.
10
Place the cushion onto the floor over the mounting
knob.
11
Open the top door and attach the handle with the two
handle screws.
placard installation
1
Remove protective plastic coating from the placard.
2
Write the location of your elephantrunk onto the
placard with a permanent marker.
3
Attach the placard to your front entry in a conspicuous
location so the courier knows where to deliver your
items.
x4
4
To activate your warranty, register your product at:
www.architecturalmailboxes.com/registration
Incoming drum can accept parcels up to
11.5" x 7.3" x 9.3".
Retrieve your parcels by unlocking the bottom door.
We're all ears!
Give us a call at (800) 464-7491 or email
© 2012, Architectural Mailboxes, LLC
Over tightening with a tool may damage
the floor and invalidate your warranty.
Swing down the "No Deliveries"
indicator to suspend deliveries.
Slide the outgoing
partition into the grooves
to trap your outgoing
parcel for future pickup.
Rev. A