Creek Audio A43 Mode d'emploi
Parcourez en ligne ou téléchargez le pdf Mode d'emploi pour {nom_de_la_catégorie} Creek Audio A43. Creek Audio A43 2 pages.
Imprimer la page
N.B.
Radio interference.
The A43 is designed to work properly in normal domestic operating conditions.
However, the amplifiers performance may be seriously affected if sited near to, or in the
room with, a working radio transmitter such as a mobile phone or CB radio, etc. Re-sit-
ing the A43, or the radio, will normalise the situation. If in doubt consult your dealer.
CREEK A43 SPECIFICATION
POWER OUTPUT (both channel)
POWER OUTPUT (one channel)
POWER OUTPUT (one channel)
POWER OUTPUT (one channel)
Not recommended for use into more than two pairs of 8Ω loudspeakers.
POWER OUTPUT (bridged mono)
Ω.
Not suitable for use into less than 8
Bridged operation can only be enabled by use of the appropriate driver board in the P43 pre-amp.
OUTPUT CURRENT (auto current limited)
TOTAL HARMONIC DISTORTION
FREQUENCY RESPONSE
SLEW RATE
SIGNAL TO NOISE RATIO (full power)
SEPARATION
POWER CONSUMPTION at idle
POWER CONSUMPTION (full power 10% THD)
WEIGHT
SIZE
MAINS VOLTAGE
@ 60Hz
@ 50Hz
MAINS VOLTAGE AND FREQUENCY IS INTERNALLY SET FOR THE COUNTRY OF USE
Creek Audio Ltd reserve the right to change or modify the specification of its products without prior warning.
Creek Audio Ltd
2 Bellevue Road, Friern Barnet, London N11 3ER, England
Tel: 00 44 + (0)181-361 4133
Fax: 00 44 + (0)181-361 4136
E-mail: [email protected]
Internet: www.creekaudio.co.uk
50 Watts into 8
Ω Ω
60 Watts into 8 Ω Ω
60 Watts into 8 Ω Ω
100 Watts into 4 Ω Ω
> 150 Watts into 8 Ω Ω
> 18 Amps RMS
< 0·03% 20 Hz to 20 kHz
3 Hz to 80 kHz - 1 dB
> 40V per µ µ S
> 100 dB A weighted
> 75 dB at 1 kHz A weighted
25 W
250 W
5.3 Kg, 12 lbs
420 x 60 x 230 mm
100V Japan, 115V North America
230/240V Europe, Asia and UK
Designed and made in the UK.
Creek A43
O O p p e e r r a a t t i i n n g g I I n n s s t t r r u u c c t t i i o o n n s s
Thank you for purchasing the A43 Power amplifier. You are now in possession of a State of
the Art Power Amplifier. The functions and operation of the A43 are extremely simple.
However, the following notes are provided to explain all aspects of its design and use.
MAINS CONNECTION
When unpacking the amplifier please keep the packing
material in a safe place for possible future use. In the pack
there is a separate mains cable suitable for connecting to
the mains supply in the country of use. The IEC socket
end of the cable should be firmly inserted into the connec-
tor on the rear panel marked "Mains Input".
Remember, do not overload the mains wall socket with too
many plugs or adaptors. The high quality performance of
the amplifier will be impaired if the electrical supply to it is
in poor condition. If in doubt, consult a qualified electrician
or your dealer.
The "Mains Input" connection is also fitted with a fuse,
specifically suited to the supply voltage of the country of
use. The correct value is clearly marked on the rear panel
next to the Mains Input.
Should it be necessary to replace the fuse, ensure that you
use the same type as specified on the rear panel. i.e. 5 x
20mm cartridge type: T 2 Amp surge resisting for 220-
240V 50Hz AC, T 4 Amp surge resisting for 110-120V
60Hz AC, T 6.3 A surge residing for 100V (Japan).