Accusplit Eagle AE180XL Mode d'emploi - Page 3

Parcourez en ligne ou téléchargez le pdf Mode d'emploi pour {nom_de_la_catégorie} Accusplit Eagle AE180XL. Accusplit Eagle AE180XL 4 pages. Accusplit pedometer operating instructions

Imprimer la page

To avoid losing or dropping your pedometer, use the included

leash and clip to fasten the pedometer securely to your

clothing.

Attaching the Leash

1. Attach the pedometer to the leash by looping the thin

side of the leash through one of the leash slots on the

sides of the pedometer case, near the bottom of the unit.

2. Put the pedometer onto your clothing as discussed above.

3. Attach the alligator clip to a belt loop or the top edge of the

pants or skirt.

Note: Y ou can also use a safety pin to fasten the leash to

your clothing, loop the leash through your belt or belt

loop, or use a badge holder.

VIEWING YOUR RESULTS

Once you put on your pedometer with the cover closed, it

will automatically begin to record your steps, activity time,

distance, and calories burned. Repeatedly press the MODE

button to cycle through the pedometer modes:

STEPS g T IME g DISTANCE g CLOCK g STEPS

Time and Distance are counted automatically whenever steps

are being counted.

• TIME is time spent in step activity.

• DISTANCE is simply stride length x steps.

Note: For extra accuracy, the default Step Filter Setting is 1.

See page 21 to learn more.

OTHER SETTINGS

The Step Filter and Unit of Measurement settings are

accessed through a special "deep set" mode.

To enter this mode, press and hold the S1 button for 4

seconds. T he screen will display a single digit. From within

Deep Set mode, press the S2 button to cycle back and forth

between the Step Filter set point and Choice of Unit System.

Can be set

from 0-5

steps

"US" (English)

or "EU" (Metric)

IGI

ALKER

.COM

STEP TIME

DIST

180

JW200

S3-

S1,S2,S4

S3+

Set measurement mode

IGI

ALKER

.COM

STEP TIME

DIST

180

JW200

S3-

S1,S2,S4

S3+

Set Step Filter set point

First, loop leash

through slot on side

of pedomete

Next, clasp clothing

Or, loop a belt

or belt loop

RESETTING YOUR PEDOMETER

Most people prefer to reset counts daily. T o reset your counts:

From STEP , T IME, or DISTANCE mode, press and hold the

yellow RESET button for at least 2 seconds. Y ou'll see the

values all go back to zero.

CHANGING STEP FILTER SETTING

While the JW200 PedometerEngine™ Step Sensor is

extremely accurate, some people like to have the ability to

filter out false steps. T herefore, the unit has a variable setting

step filter, to allow fine-tuning to your specific preferences.

You can set the value to any value from 0 – 5 steps. For

example, if the filter is set to "3" , the unit will wait to start

counting steps until more than three steps have been taken in

less than five seconds.

Press S3+ (MODE) or S3– (RESET) to change the Step Filter

Setting.

CHANGING UNITS (English vs. Metric)

The Pedometer can display either in English units (in, mi, and lb

- this is the default), or in Metric units (cm, km, and kg). From within

Deep Set mode (see pg. 25), press the S2 button to cycle back and

forth between setting the Step Filter set point and Choice of Unit

System. T he unit will show either "US" or "EU" (for European Union)

depending on the unit system chosen. If you change units after using

the pedometer, the unit will convert all of your data into the new unit

system when you exit Deep Set model. Y ou can check to see which

system of units you are using by seeing which measurement units

are displayed on the Stride and Weight setting screens.

Press S3+ (MODE) or S3– (RESET) to change the Measurement Mode.

Press and hold S4 for 2 seconds to exit Deep Set Mode.

Note: T he unit will save any changes and exit set mode after 30

seconds unattended.

Or, loop a

badge holder, then

put into pocket

(Badge holder

not included)