Accustat ES-H1 Mode d'emploi

Parcourez en ligne ou téléchargez le pdf Mode d'emploi pour {nom_de_la_catégorie} Accustat ES-H1. Accustat ES-H1 3 pages.

Imprimer la page

Installation and Operating Instructions

ES-H1

Environmentally Friendly

MERCURY FREE!!

Use ONLY ACCUSTAT®

Temperature Setpoints

Application:

The ACCUSTAT®

to operate 24VAC to 30VAC heating systems. This thermostat is

MERCURY FREE!! The ACCUSTAT®

pre-set plug-in temperature setpoints to activate the circuits. Room air

temperature is measured by a microprocessor and compared with the

plug-in setpoint temperature. The thermostat has a locking cover to

prevent tampering.

Operating Conditions:

The electronic mechanisms incorporated within this unit REQUIRE

operating conditions similar to other electronic devices intended for

INDOOR USE ONLY, such as would be acceptable for TV and similar

household appliances. Relative humidity must be less than 95% and

the atmosphere must be non-condensing. Air quality must be main-

tained, FREE of heavy dust or debris which may infiltrate the interior

of this device. Installation in any space which is unfinished or under-

going repainting or general rehabilitation is also considered product

abuse. This device should be removed from service during any local

construction activity.

Cleaning:

This device incorporates a high impact styrene enclosure which is

easily cleaned with a dry cloth or vacuum brush. Occasional soiling

may be cleaned with a soft cloth lightly dampened with water and/or

mild cleaning solution. IN NO CASE should this device be directly

sprayed with or exposed to free flowing liquids, including water, which

could penetrate its interior.

FAILURE TO OBSERVE ANY OF THE ABOVE CONDITIONS OF USE

WILL COMPLETELY VOID THE SUPPLIER WARRANTY.

CAUTION

MAKE SURE UNIT IS PROPERLY CONNECTED. DAMAGE TO THE

CONTROL CAN BE CAUSED BY MISWIRING, WHICH WILL VOID

THE WARRANTY.

HEAT

OFF ON

model ES-H1 thermostat was designed

models utilize

Specifications:

Set Temperature Range: Determined by plug-in setpoint

Plug-in Setpoint Accuracy: ± 0.5°

Control Accuracy: ± 1.0°

Sampling Rate: Every 30 seconds

System: Switch selectable, heat on or off

Stages: Single stage heating

Differential: Switch selectable, 0.5° or 1.0°

Operating Temperature: 14°F to 105°F

Storage Temperature: -4°F to 105°F

Input: 20VAC to 32VAC

Load Rating: 1 amp maximum per circuit, 80mA minimum for

energy harvesting

Cycle Rate: 6 cycles per hour

Common Wire: Optional

Delay: 5 minutes on start-up

Energy Harvesting: Switch selectable, on or off

Enable switch if not connecting a common wire

Disable switch for sensitive loads, common wire will then be required

Thermostat Charge: Thermostat will hold its charge 3.5 hours during

a power failure

Enclosure: High impact styrene, white

Case can be locked, key required

TO OPEN:

1. Align key with slot and insert all the way

2. Locking pin will emerge. Pull out completely

3. Gently squeeze left side of cover to

release catches

4. Let right side work as a hinge

Swing cover out and remove

Squeeze

Insert

TO CLOSE: (Reverse Procedure)

1. Hinge right side of cover and close it

2. Gently squeeze left side of cover and

snap shut

3. Orient the locking pin as shown and

slide in until end is below surface of

cover (audible snap is heard when

pin is properly seated)

ATTENTION: This product does not contain mercury.

This product may be replacing a product containing

mercury.

Do not place the old product in the household trash.

For more information on recycling and proper disposal

visit TRC's website www.thermostat-recycle.org

Should a tube break, do not touch any spilled mercury.

Wear non-absorbent gloves, collect any spilled mercury

and place it in a sealed container. Contact your local waste

management authority for recycling and proper disposal

instructions.

Lift and

Rotate

Remove