FIBARO FGK-101 Manuel d'utilisation - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} FIBARO FGK-101. FIBARO FGK-101 2 pages. Door / window sensor

Imprimer la page

V Configuration

The Door / Window Sensor offers a wide range of advanced

settings. The parameters listed below are available in the

Fibaro configuration interface.

Fig. 1 - Door / Window Sensor icon

in the Home Center controller

In order to configure the Fibaro Door / Window Sensor (using the

Home Center 2 controller) go to the device options by clicking on

the icon:

Next, select the device options tab.

Device parameters:

Parameter no. 1

Input IN alarm cancellation delay.

Additional delay after an alarm from input IN has ceased. The

parameter allows user to specify additional time, after which the

input IN alarm is cancelled once its violation has ceased.

Default value: 0

Available parameter settings: 0 – 65535 s

Fig. 2 - DS18B20 temperature sensor icon

Parameter value: 2 [byte]

in the Home Center controller

Parameter no. 2

Sensor used without a DS18B20 sensor, or used with a switch

Status change signalled by LED

connected to IN input, will be represented by single icon. After the

DS18B20 temperature sensor has been connected, temperature

Default setting: 1

sensor icon will be displayed.

Available parameter settings:

0 - LED turned Off,

1 - LED turned On.

NOTE!

If a temperature sensor icon is not displayed

Parameter value: 1 [byte].

despite the fact the sensor itself has been

connected, or if the temperature readings are

incorrect, inspect the connections on the 1-wire

bus, in particular the connection between sensor

Parameter no. 3

outputs and the line, and the total length of the bus

Type of IN input.

wire which should not exceed 30m.

Default value: 0 – INPUT_NC (Normal Close)

Available parameter settings:

0 – INPUT_NC (Normal Close)

1 – INPUT_NO (Normal Open)

2 – INPUT_MONOSTABLE

IV Association

3 – INPUT_BISTABLE

Parameter value: 1 [byte].

Association allows the Fibaro Door/Window Sensor to directly

control another device in the Z-wave network, e.g. Dimmer, Switch

(On-Off), Roller Shutter or trigger scenes (scene control is only

possible via the Home Center 2 controller).

Parameter no. 5

Type of control frame transmitted for association group 1, activated

via IN input. The parameter allows you to specify the type of an

NOTE!

alarm frame or to force control frames transmission (BASIC_SET)

Association allows for direct transmission of control

commands between devices and takes place without

Default value: 255 – BASIC SET

the participation of the main controller. Owing to this

mechanism

the

Door/Window

Sensor

may

Available parameter settings:

communicate with devices even if the main controller

0 – ALARM GENERIC frame

is completely destroyed, e.g. in the event of a fire.

1 – ALARM SMOKE frame

2 – ALARM CO frame

3 – ALARM CO2 frame

4 – ALARM HEAT frame

5 – ALARM WATER frame

The Fibaro Door/Window Sensor supports three association

255 – Control frame BASIC_SET

groups.

Parameter value: 1 [byte].

Group I is assigned to input IN1 (and the magnetic sensor).

Sending BASIC SET or ALARM command frames.

Group II is assigned to TMP button. Once the button is released,

ALARM GENERIC frame is sent to associated devices.

Parameter no. 7

Value of the parameter specifying the forced level of dimming/ope-

Group III reports on the condition of the device, only one device

may be assigned to the group (main controller, by default).

ning roller blinds when "switch on"/"open" commands are sent to

devices from association group no.1.

The Fibaro Door/Window Sensor allows for control over 5 regular

devices and 5 multichannel devices per group, out of which 1 field

In case of alarm frames an alarm priority is specified.

is reserved for the network controller.

Default value: 255

In order to add an association (with the use of the Home Center 2

Possible parameter settings: (1 – 99) and 255

controller) go to device options by clicking this icon:

Value of 255 makes it possible to activate a device. In case of the

Dimmer module it means activating the device and setting it to the

Select the device options tab. Next specify which devices will be

previously stored condition, e.g. when Dimmer is set to 30%,

deactivated and then reactivated using 255 commend, it will be

associated, and to which association groups. Sending of

automatically set to the previous condition i.e. 30%.

configuration commands to associated devices might take up to a

few hours, depending on previous devices settings and the number

of devices within the network.

Parameter value: 1 [byte].

Parameter no. 9

Deactivating transmission of the alarm cancelling frame or the

NOTE!

Any new association order given while any

control frame deactivating the device (Basic). It allows for disabling

the function of deactivating the device and cancelling alarms for

association commands are already being sent to

devices associated with IN input.

devices, cancels previous one.

Default value: 0

Available parameter settings:

0 – for association group no. 1 information is sent

1 – for association group no. 1 information is not sent.

Parameter value: 1 [byte].

NOTE!

The parameter cancels alarms only. Information on

alarm violation or activation commands for devices

from association groups are always sent.

Parameter no. 12

Sensitivity to temperature changes. The maximum acceptable

difference between the last reported temperature and the current

temperature read from the sensor. If the temperatures differ by the

set value or more, a report with the current temperature value is

sent to the device assigned to association group no. 3.

Default value: 8 [0,5oC]

Available parameter settings: 0 – 255 [0oC to 16oC] [32oF –

60,8oF]

To set an appropriate parameter value use the following formula:

x = delta T x 16 - for Celsius

x = delta T x 80 / 9 - for Fahrenheit

x = parameter value

delta T – maximum acceptable temperature gradient in Celsius or

Fahrenheit

If the value is set to 0:

- if the wake-up interval is set to 255 seconds, temperature report

will be sent according to the interval,

- if the wake-up interval is set to over 255, temperature report will be

sent each ca. 4 minutes.

Parameter value: 1 [byte].

Parameter no. 13

Sending an alarm or control frame (for IN input, depending on

parameter no.5 value), and TMP button alarm frame. The frame is

sent in "broadcast" mode,

information sent in this mode is not repeated by the mesh network.

Default value: 0

Available parameter settings:

0 – IN and TMP Broadcast mode inactive,

1 – IN broadcast mode active, TMP broadcast mode inactive

2 – IN broadcast mode inactive, TMP broadcast mode active

3 – IN and TMP broadcast mode active

Parameter value: 1 [byte].

NOTE!

If the "broadcast" mode of information transmission

is activated for a given channel, then transmission of

information in "singlecast" mode, i.e. to devices

assigned to the association group, for this channel is

deactivated.

Parameter no. 14

Scene activation functionality.

Default value: 0

Available parameter settings:

0 - functionality deactivated

1 - functionality activated

The device offers the possibility of sending commands compatible

with Command class scene activation. Information is sent to

devices assigned to association group no. 3

Controllers such as the Home Center 2 are able to interpret such

commands and based on these commands activate scenes, to

which specific scene IDs have been assigned. The user may

expand the functionality of a button connected to IN input by

distinguishing the sequence of it being pushed. For example:

double click would trigger the "goodnight" scene and triple click

would trigger the "morning" scene. To fully use the possibilities

offered by the parameter no.14 it is recommended to use a

momentary or a toggle switch (parameter no.3).

Scene ID is determined in the following manner:

IN input:

Switch from "off" to "on" ID10

Switch from "on" to "off" ID11

Remaining IDs are recognized correctly if the value of parameter

no.3 was set to 2

Holding down ID12

Releasing ID13

Double click ID14

Triple click ID15

Parameter value: 1 [byte].

NOTE!

Scene activation functionality may shorten the

battery life, even by 25%.

VI Additional Functionality

Alarm Frame Support.

The Fibaro System allows you to set the device's reaction to alarms

(reaction to SENSOR_ALARM_REPORT frame). The Fibaro

Door/Window Sensor sends alarm frames of different types,

depending on parameter's no. 5 settings. The user should declare

type of alarm frame for each connected sensor. For example, for a

smoke detector connected to IN input the user should declare the

type 1–ALARM SMOKE frame (value of 1 should be entered), to

ensure the remaining Z-Wave network devices recognize the

information on smoke detector alarm correctly.

VII Door / Window Sensor operation

The Fibaro Door/Window Sensor may be operated using:

• Any System compatible controller (e.g. Home Center 2)

• Cellular phone (e.g. iPhone or phones from other manufacturers,

with the proper control application)

• PC, with the use of an Internet browser,

• Tablets (e.g. iPad)

• Using the TMP button, located inside the housing.

VIII Procedure to be followed in case of interference

The Device does not react to a programmed transmitter:

• Make sure the maximum range has not been exceeded and there

are no obstacles along the signal path containing metal surfaces,

e.g. metal cabinets, Ferro concrete ceiling, load bearing walls, etc.

• Make sure the device is not in the learning mode.

• Alternately repeat the programming process.

IX Guarantee

1. The Guarantee is provided by FIBAR GROUP Sp. z o.o.

(hereinafter "Manufacturer"), based in Poznan, ul. Lotnicza 1;

60-421 Poznan, entered in the register of the National

Department of the National Court Register, no. 370151, NIP

7811858097, REGON: 301595664.

i.e. to all devices within range -

2. The Manufacturer is responsible for equipment malfunction

resulting from physical defects (manufacturing or material) of the

Device for 12 months from the date of its purchasing.

3. During the Guarantee period, the Manufacturer shall remove any

defects, free of charge, by repairing or replacing (at the sole

discretion of the Manufacturer) any defective components of the

Device with new or regenerated components, that are free of

defects. When the repair impossible, the Manufacturer reserves the

right to replace the device with a new or regenerated one, which

shall be free of any defects and its condition shall not be worse than

the original device owned by the Customer.

4. In special cases, when the device cannot be replaced with the

device of the same type (e.g. the device is no longer available in the

commercial offer), the Manufacturer may replace it with a different

device having technical parameters similar to the faulty one. Such

activity shall be considered as fulfilling the obligations of the

Manufacturer. The Manufacturer shall not refund money paid for the

device.

5. The holder of a valid guarantee shall submit a guarantee claim

through the guarantee service. Remember: before you submit a

guarantee claim, contact our technical support using telephone or

e-mail. More than 50% of operational problems is resolved

remotely, saving time and money spent to initiating guarantee

procedure. If remote support is insufficient, the Customer shall fill

the guarantee claim form (using our website - www.fibargroup.com)

in order to obtain claim authorization.

When the guarantee claim form is submitted correctly, the

Customer shall receive the claim confirmation with an unique

number (Return Merchandise Authorization -RMA).

6. The claim may be also submitted by telephone. In this case, the

call is recorded and the Customer shall be informed about it by a

consultant before submitting the claim. Immediately after submitting

the claim, the consultant shall provide the Customer with the claim

number (RMA-number).

7. When the guarantee claim form is submitted correctly, a

representative of the Authorised Guarantee Service (hereinafter as

"AGS") shall contact the Customer.

8. Defects revealed within the guarantee period shall be removed

not later than 30 days from the date of delivering the Device to AGS.

The guarantee period shall be extended by the time in which the

Device was kept by AGS.

9. The faulty device shall be provided by the Customer with

complete standard equipment and documents proving its purchase.

10. Parts replaced under the guarantee are the property of the

Manufacturer. The guarantee for all parts replaced in the guarantee

process shall be equal to the guarantee period of the original

device. The guarantee period of the replaced part shall not be

extended.

11. Costs of delivering the faulty device shall be borne by the

Customer. For unjustified service calls, the Service may charge the

Customer with travel expenses and handling costs related to the

case.

12. AGS shall not accept a complaint claim only when:

• the Device was misused or the manual was not observed,

• the Device was provided by the Customer incomplete, without

accessories or nameplate,

• it was determined that the fault was caused by other reasons than

a material or manufacturing defect of the Device

• the guarantee document is not valid there is no proof of purchase,

13. The Manufacturer shall not be liable for damages to property

caused by defective device. The Manufacturer shall not be liable for

indirect, incidental, special, consequential or punitive damages, or

for any damages, including, inter alia, loss of profits, savings, data,

loss of benefits, claims by third parties and any property damage or

personal injuries arising from or related to the use of the Device.

14. The guarantee shall not cover:

• mechanical damages (cracks, fractures, cuts, abrasions, physical

deformations caused by impact, falling or dropping the device or

other object, improper use or not observing the operating manual);

• damages resulting from external causes, e.g.: flood, storm, fire,

lightning, natural disasters, earthquakes, war, civil disturbance,

force majeure, unforeseen accidents, theft, water damage, liquid

leakage, battery spill, weather conditions, sunlight, sand, moisture,

high or low temperature, air pollution;

• damages caused by malfunctioning software, attack of a

computer virus, or by failure to update the software as recommen-

ded by the Manufacturer;

• damages resulting from: surges in the power and/or telecommuni-

cation network, improper connection to the grid in a manner

inconsistent with the operating manual, or from connecting other

devices not recommended by the Manufacturer.

• damages caused by operating or storing the device in extremely

adverse conditions, i.e. high humidity, dust, too low (freezing) or too

high ambient temperature. Detailed permissible conditions for

operating the Device are defined in the operating manual;

• damages caused by using accessories not recommended by the

Manufacturer

• damages caused by faulty electrical installation of the Customer,

including the use of incorrect fuses;

• damages caused by Customer's failure to provide maintenance

and servicing activities defined in the operating manual;

• damages resulting from the use of spurious spare parts or

accessories improper for given model, repairing and introducing

alterations by unauthorized persons;

• defects caused by operating faulty Device or accessories.

15. The scope of the guarantee repairs shall not include periodic

maintenance and inspections, in particular cleaning, adjustments,

Court

operational checks, correction of errors or parameter programming

and other activities that should be performed by the user (Buyer).

The guarantee shall not cover natural wear and tear of the Device

and its components listed in the operating manual and in technical

documentation as such elements have a defined operational life.

16. If a defect is not covered by the guarantee, the Manufacturer

reserves the right to remove such defect at its sole discretion,

repairing the damaged or destroyed parts or providing components

necessary for repair or replacement.

17. This guarantee shall not exclude, limit or suspend the Customer

rights when the provided product is inconsistent with the purchase

agreement.

This Device may be used with all devices

certified with Z-Wave certificate and should be

compatible with such devices produced by

other manufacturers.

Any device compatible with Z-Wave may be added

to Fibaro system.

FIBARGROUP

FIBARO

In case of any technical questions contact customer service centre

in your country.