Sharp Aquos LC-13B8U Manuel d'utilisation - Page 14
Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Sharp Aquos LC-13B8U. Sharp Aquos LC-13B8U 39 pages. Sharp television lc-13b8u operation manual
Imprimer la page
Setting the CLOCK
AUTO CLOCK Setting
There are two methods of setting the clock: AUTO CLOCK
and MANUAL CLOCK. AUTO CLOCK uses EDS signals,
which are provided by some TV stations, to automatically
adjust the clock. MANUAL CLOCK sets the clock manually in
areas where no channel carries EDS signals.
1
Press MENU to display the Menu screen.
2
Press \/| to select "SETUP".
Press '/" to select "CLOCK", and press ENTER.
3
SETUP
OPTION
C H – S E T T I N G
M T S
C L O C K
I N P U T 3
S E L E C T
V – C H I P
B L O C K
C L O S E D
C A P T I O N
C O L O R
S Y S T E M
L A N G U A G E
4
Press '/" to select "SET", and press ENTER.
S E T
T I M E
D I S P L A Y
5
Press '/" to select "AUTO", and press ENTER.
● If you do not know the channel that carries EDS signals in your
area, set "EDS CH" to "AUTO" and press ENTER. If you know the
channel of the EDS signal carrier in your area, press \/| to select
the channel and press ENTER.
S E T
T I M E
D I S P L A Y
● When set to "AUTO CLOCK", the current time is acquired
automatically when the main power is turned OFF. (This function
will not work when EDS CH is not set.)
■ Backup
The clock function is maintained for about 5 minutes even
when the AC cord has been shut off due to a power outage
or when moving the LCD TV set. (Since about 30 minutes
are required to charge the backup power supply, it may not
be possible to maintain the clock function if the charging time
is excessively short.)
If the clock setting has been reset, repeat the procedures on
this page.
A U T O
M A N U A L
E D S
C H
A U T O
A
• CLOCK:
The AUTO CLOCK setting may take from several minutes to an hour
depending on the number of channels to receive and signal status.
• EDS CH < AUTO >:
If there are no channels with EDS signals or the antenna signal is
weak, the AUTO CLOCK Setting may not operate. In such a
case, the message "EDS CH IS NOT AVAILABLE." appears, and
the CLOCK setting screen (in step 4 in AUTO CLOCK Setting) is
displayed. Refer to MANUAL CLOCK Setting to set the clock
manually.
• EDS CH < Not AUTO >:
If the channel you have selected for "EDS CH" is wrong or the EDS
signal carrier is weak, or when there is no broadcast, the AUTO
CLOCK Setting may not operate. In such cases, the message
"EDS CH (XXX) EDS DATA IS NOT AVAILABLE." appears, and
the CLOCK setting screen (in step 4 in AUTO CLOCK Setting) is
displayed as in the case with EDS CH < AUTO >. Follow step 4
and repeat the AUTO CLOCK Setting procedure.
• If broadcasting channels are not memorized, EDS signals cannot
be received even when the "EDS CH" is set to "AUTO". In this
case, try EZ SETUP again. (See page 21.)
MANUAL CLOCK Setting
If there are no channels with EDS signals, set the clock
manually using MANUAL CLOCK.
1
Repeat steps 1 to 4 of AUTO CLOCK Setting.
2
Press '/" to select "MANUAL", and press ENTER.
S E T
T I M E
D I S P L A Y
3
Press '/" to select "DST", and press \/| to select
"ON" or "OFF".
Press '/" to select "TIME", and press \/| to set the
time, and press ENTER.
12:00AM
11:59AM
11:59PM
12:00PM
• Holding down \/| changes the setting at a high speed.
S E T
T I M E
D I S P L A Y
4
Press MENU to exit.
A
• Make sure to press ENTER after adjusting the time. Otherwise,
the time will not be set.
• When "DST" is set to "ON", the time entered is forwarded by 1
hour.
• Please be sure to set "DST" before setting "TIME".
A U T O
M A N U A L
D S T
O F F
0 0
T I M E
1 2 :
A M
13