Crestron 6508043 Manuel d'installation - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel d'installation pour {nom_de_la_catégorie} Crestron 6508043. Crestron 6508043 2 pages. Shutter motor controller

Imprimer la page

Local and Remote Mode

The CLCI-MCEX can operate in Local mode (without the use of a control system) or in

Remote mode (with the use of a control system). The functionality and the type of switch

that can be used differs based on the operating mode.

NOTE: Before using the CLCI-MCEX, ensure the device is using the latest firmware.

Check for the latest firmware for the CLCI-MCEX at www.crestron.com/firmware.

Firmware is loaded onto the device using Crestron Toolbox™ software.

Local Mode

In Local mode, the CLCI-MCEX is controlled using a momentary switch. When the

momentary switch is pressed, the shutter motor cycles through open, stop, close, and

stop functions. For example, if the shutter motor was opened and then stopped, on the

next press the shutter motor closes the shutters. The press after that stops the shutter

motor.

NOTE: Holding the momentary switch performs no action.

Remote Mode

In Remote mode, the device must be connected to a control system. Changing the symbol

in the control system program from momentary to maintained allows a maintained switch

to be used with the device. When the maintained switch is up, the shutter motor opens the

shutters. When the maintained switch is down, the shutter motor closes the shutters.

NOTE: There is no option to stop the shutter motor when using a maintained switch.

Set Open and Close Times

To determine the maximum open and close heights for the motor, the CLCI-MCEX utilizes

max open and max close times. The max open and max close time ranges between 1

second and 360 seconds and is set up in the symbol.

Setup Button Function

The Setup button allows the CLCI-MCEX to join an infiNET EX network and to provide

shutter motor control. Refer to "Wireless Communications" for joining an infiNET EX

network.

The Setup button also provides a means of controlling the motor. Press and hold the

Setup button to open or close the shade or shutter. Release the Setup button to stop the

motor. Press and hold the Setup button again to reverse the direction of shutter motor.

Wireless Communications

The device connects to the Crestron network via the infiNET EX communications protocol.

Use the procedures outlined below to join or leave an infiNET EX network and to verify

communications between the device and the control system.

Joining an infiNET EX Network

Before a device can be used in a lighting system, it must first join an infiNET EX network.

To join an infiNET EX network, the device must be acquired by an infiNET EX gateway.

NOTE: A device can be acquired by only one gateway.

1. Put the infiNET EX gateway into Acquire mode from the unit itself or from Crestron

Toolbox. Refer to the gateway's manual at

NOTE: In an environment where multiple gateways are installed, only one

gateway should be in Acquire mode at any time.

2. Put the device into Acquire mode.

NOTE: The acquire process can also be initiated by a remote maintained switch

or remote momentary switch (if equipped). Flip the maintained switch or press

the momentary switch four times rapidly to enter Acquire mode, the Chan. 1 LED

flashes (this can take up to 10 seconds).

a. Tap the Setup button three times and then press and hold it down (tap-tap-tap-

press+hold) until the Chan. 1 and Chan. 2 LEDs on the device flash once (this can

take up to 10 seconds).

As of the date of manufacture, the product has been tested and found to comply with specifications

for CE marking.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following

conditions:(1) This device may not cause harmful interference and (2) this device must accept any

interference received, including interference that may cause undesired operation.

CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for

compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

www.crestron.com/manuals

for details.

b. Release the button to start the acquire process. Chan. 1 LED and the attached

load will flash slowly to show that the device is actively scanning the infiNET EX

network.

• Chan. 1 LED turns on for 5 seconds to show that the device has been

successfully acquired by the infiNET EX network.

• If the device fails to acquire, the Chan. 1 LED flashes rapidly until a button

is pressed. Ensure the gateway is in Acquire mode and within range before

attempting the acquire process again.

3. Once all devices have been acquired, take the gateway out of Acquire mode. Refer

to the gateway's manual for details.

Leaving an infiNET EX Network:

1. Verify that the device is not within range of a gateway that is in Acquire mode.

2. Press the Setup button three times, and then press and hold it down (tap-tap-tap

press+hold) until the Chan. 1 LED on the device flashes once (this can take up to

10 seconds), then release the button. The LED flashes slowly.

3. The LED then flashes quickly to indicate that the device has left the infiNET EX

wireless network.

4. Press the Setup button to confirm that the device has left the infiNET EX wireless

network

Verifying Communications Status

To check the communications status of the device, tap the Setup button three times and

then press and hold it down (tap-tap-tap-press+hold) for up to 2 seconds. The Chan. 1

LED flashes to indicate the communications status. Refer to the following table for details.

LED

Turns on for 5 seconds

The device is communicating with the control system.

Flashes three times

The device is communicating with the gateway, but the

gateway is not communicating with the control system.

Flashes twice

The device was previously joined to the network but is not

communicating with the gateway.

Flashes once

The device is not joined to the network.

Specifications

The specifications for the CLCI-MCEX are listed below.

SPECIFICATION

Input Voltage

220-240 VAC, 50/60 Hz line power

Max Load

2.5 A FLA @ 240 VAC

15 A LRA @ 240 VAC

Environmental

Temperature

0º to 40 ºC (23º to 104 ºF)

Humidity

10% to 90% RH (noncondensing)

Industry Canada (IC) Compliance Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

The product warranty can be found at www.crestron.com/warranty.

The specific patents that cover Crestron products are listed at www.crestron.com/legal/patents.

Certain Crestron products contain open source software. For specific information, please visit

www.crestron.com/opensource.

Crestron, the Crestron logo, Crestron Toolbox, and infiNET EX are either trademarks or registered

trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks,

registered trademarks, and trade names may be used in this document to refer to either the entities

claiming the marks and names or their products. Crestron disclaims any proprietary interest in the

marks and names of others. Crestron is not responsible for errors in typography or photography.

This document was written by the Technical Publications department at Crestron.

Crestron Electronics, Inc.

15 Volvo Drive, Rockleigh, NJ 07647

Tel: 888.CRESTRON

Fax: 201.767.7576

www.crestron.com

COMMUNICATIONS STATUS

DETAILS

Installation Guide - DOC. 7929A

(2049999)

Specifications subject to

change without notice.

05.18