Crestron FlipTop FT2 Series Manuel de démarrage rapide - Page 3

Parcourez en ligne ou téléchargez le pdf Manuel de démarrage rapide pour {nom_de_la_catégorie} Crestron FlipTop FT2 Series. Crestron FlipTop FT2 Series 7 pages. Ac power outlet modules
Également pour Crestron FlipTop FT2 Series : Démarrage rapide (2 pages), Démarrage rapide (2 pages), Manuel de démarrage rapide (11 pages), Manuel de démarrage rapide (2 pages), Manuel de démarrage rapide (11 pages), Manuel de démarrage rapide (9 pages), Manuel de démarrage rapide (9 pages), Manuel de démarrage rapide (11 pages), Pour commencer (2 pages), Pour commencer (2 pages), Pour commencer (2 pages), Manuel (2 pages), Manuel (2 pages), Manuel (2 pages), Manuel de démarrage rapide (8 pages), Démarrage rapide (2 pages), Manuel de démarrage rapide (2 pages), Démarrage rapide (2 pages), Démarrage rapide (2 pages), Manuel de démarrage rapide (2 pages), Démarrage rapide (2 pages), Démarrage rapide (2 pages)

Imprimer la page
Crestron FlipTop FT2 Series Manuel de démarrage rapide
FT2-1400-MECH-PTL
FlipTop™ FT2 Series Cable Management System, 1400 Size, Mechanical, Pass-Through Lid

Install the Modules

All modules are sold separately and not included with the
FT2-1400-MECH-PTL FlipTop assembly. Installation procedures for
most modules are available in separate product documentation. For
more information, refer to the specific product manual located at
www.crestron.com/manuals.
The following sections provide best practices and installation procedures
for pass-through cable modules and blank plate modules.
Module Best Practices
Follow the best practices below when performing module installation.
Perform module installation in the following order:
l
1. AC Power Outlet Modules (FT2A-PWR-US, FT2A-PWR-EU,
FT2A-PWR-AU, FT2A-PWR-FR, FT2A-PWR-IS, FT2A-PWR-IT,
FT2A-PWR-SW, FT2A-PWR-UK, and FT2A-PWR-UN)
2. Retractor modules
(FT2A-CBLR-GR
3. All other modules
(FT2A-CP
FT2A-PLT-PT, and FT2A-PLT-BLANK)
Place the FT2A-CBLR-GR modules only at the ends of a module row.
l
Dress all cables after installing each module.
l
Pass-Through Cable Module
The FT2A-PLT-PT pass-through modules (sold separately) enable
FT2-CBL-PT pass-through cables (sold separately) and other types of
interface cables to be installed within the FT2-1400-MECH-PTL. Each
FT2A-PLT-PT cable module is packaged with a nylon grommet and a
cable plate. An empty module slot in the FT2-1400-MECH-PTL and an
FT2-CBL-PT series or other interface cable are required for installation.
series)
series,
FT2A-CHGR
series,
Installing the Pass-Through Cable Module with 4K Cables
The included grommet is not needed when installing most 4K cables. If
the cable is 10 mm or thinner, the grommet may be used.
1. Push the connector end of the cable through the hole in the cable
plate.
2. Insert the cable plate into one of the three slots in the pass-through
module. Choose the appropriate slot based on the length of the cable
connector. The top of the connector must sit flush with the top of the
module.
NOTES:
If the connector extends past the top of the pass-through
l
module, the lid cannot close.
Ensure that the cable moves freely in the module prior to
l
attaching the side plate. The plate is difficult to remove once it is
attached.
Quick Start
3