Bittel HWD9838TSD-T Manuel de l'utilisateur - Page 4
Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} Bittel HWD9838TSD-T. Bittel HWD9838TSD-T 5 pages.
Imprimer la page
3.9 Mute
Off-hook mode, press MUTE key to stop the sending, re-
press MUTE remove the mute mode (The MUTE indicator
of the base will turn on).
3.10 Adjust ringer volume
On-hook, press VOL+/VOL- to adjust the ringer volume.
Note: Pressing VOL won't adjust the volume if the
reception is set to auto recover.
3.11 Memory keys (Only work when outside
power is available)
a. How to Store:
On-hook mode, press HOLD (for one-line, hold indicator
will turn and for two-line CONF indicator will turn on)+
Desired number ( twenty-four number at most)
+MEMORY key / MWL key
b. How to use
The use of the memory keys of the base: The handset is
in off-hook status, press the memory key of the base, the
number will be dialed out. The base is in off-hook status,
just need directly press certain memory keys; On-hook
status, directly press the memory buttons, the base will
auto off-hook and dial out the number of the memory key,
which can be set as followed:
Base is in on-hook status: press HOLD+#+ Memory key
will make the base auto off-hook and dial out the number
stored in the memory keys
c. How to delete the stored number in the memory key
With outside power, press the HOLD + Memory
keys/MWL of the base can delete the stored number.
3.12 MWL
When there is new message, the MWL will flash, press
MWL key can retrieve the message
3.13 Register and delete the Handset
First please connect the outside power and correctly
install the battery into the handset, then correctly put
the handset into the base. Please put the handset back
to the base when the base in on-hook status. The charging
indicator should be on, then off, then on. After 5-10
seconds, please press REDIAL of the base, if the handset
rings, it means the registration succeeds.
4 Maintenance and troubleshooting
4.1 No ringing or no continually ringing
Check the telephone line
Check the quantity of parallel phone set
Check the ringer switch position
4.2 Handset doesn't work
Press LINE key and the indicator sound: Handset not
register and need register again.
The distance is far from Base to Handset, back to around
Base.
Power low and need recharge.
4.3 Handset not work momentary
Poor signal for Handset, wait a moment will resume automatically.
BITTEL ELECTRONICS CO., LTD.
When the device met some trouble, don't open by
yourself, it's better to contact your distributor or local
service center.
4.4 About Battery:
a.If the battery hasn't been used for over 5 months after
first charging or stored, it needs charge last 8 hours for
normal use.
b. The new battery must pass 3-4 times charging and
using will reach the peak performance.
c. If the device does not use for long time, please unplug
the battery from the socket and stored in dry
environment
d. If long time no use, it will recover after fully charged
and discharged for several times
e. Don't discharge by man-made.
f. Please change the battery after using 20 months.
Suggest to buy from our factory directly.
Note: 1. We won't supply the warranty if the battery are
damaged by not charging for long time.
2. Please make sure that the batteries are installed
before charging.
5 Approval
5.1 FCC APPROVAL
Complies with Part 68 of the FCC rules. On the
bottom of this telephone is a label that contains,
among other information, the FCC registration
number and the ringer equivalence number (REN) for
this telephone. If requested, you must provide this
information to the Telephone Company.
5.2 CE APPROVAL
Complies with CE approval.
5.3 JACKS
Uses RJ11C USOC standard modular jacks.
6 Service
6.1 WARRANTY
This product is warranted for a period of 12 months
from the date of purchase against faulty materials or
workmanship. If during this period a defect arises, we
may repair or replace the product, at Bittel's discretion,
provided that:
1) The product has not been used for any purpose other
than normal use,
2) Unauthorized product repair or modifications have not
been attempted.
3) The product has never been used in a harsh or
corrosive environment.
4) No damage in transit
---- Page 4----