Cisco 6941 - Unified IP Phone Slimline VoIP Manuel de configuration - Page 3

Parcourez en ligne ou téléchargez le pdf Manuel de configuration pour {nom_de_la_catégorie} Cisco 6941 - Unified IP Phone Slimline VoIP. Cisco 6941 - Unified IP Phone Slimline VoIP 16 pages. Two-line ip endpoint supporting both video and light-to-moderate voice communications
Également pour Cisco 6941 - Unified IP Phone Slimline VoIP : Fiche technique (5 pages), Notes de mise à jour (18 pages), Fiche technique (5 pages), Manuel de l'utilisateur (38 pages), Manuel d'administration (14 pages), Caractéristiques (29 pages), Manuel de l'utilisateur (24 pages), Manuel de référence rapide (2 pages), Manuel de démarrage rapide (2 pages), Manuel de référence (4 pages), Carte de référence rapide (2 pages), Manuel d'administration (19 pages), Manuel d'utilisation (7 pages), Manuel de référence rapide (2 pages), Manuel de démarrage rapide (4 pages)

Chapter

Each port supports 10/100 Mbps half- or full-duplex connections to external devices. Cisco Unified IP

Phone 6945 also supports 1000 Mbps full-duplex connections to external devices.You can use either

Category 3/5/5e cabling for 10-Mbps connections, but you must use Category 5/5e for 100 or 1000

Mbps connections.

Use the SW network port to connect the phone to the network. You must use a straight-through cable on

this port. The phone can also obtain inline power from a switch over this connection. See the

Phones to the Cisco Unified CM Database" section on page 2-8

Use the PC access port to connect a network device, such as a computer, to the phone. You must use a

straight-through cable on this port.

Handset

The handset is designed especially for use with a Cisco Unified IP Phone. It includes a light strip that

indicates incoming calls and voice messages waiting.

To connect a handset to the Cisco Unified IP Phone, plug the cable into the handset and the Handset port

on the back of the phone.

Speakerphone

By default, the speakerphone is enabled on the Cisco Unified IP Phone.

You can disable the speakerphone by using Cisco Unified Communications Manager Administration. To

do so, choose Device > Phone and locate the phone you want to modify. In the Phone Configuration

window for the phone, check the Disable Speakerphone check box.

Headset

Although Cisco Systems performs internal testing of third-party headsets for use with the Cisco Unified

IP Phones, Cisco Systems does not certify or support products from headset or handset vendors.

Cisco recommends the use of good quality external devices, for example, headsets that are screened

against unwanted radio frequency (RF) and audio frequency (AF) signals. Depending on the quality of

headsets and their proximity to other devices such as cell phones and two-way radios, some audio noise

or echo may still occur. An audible hum or buzz may be heard by either the remote party or by both the

remote party and the Cisco Unified IP Phone user. Humming or buzzing sounds can be caused by a range

of outside sources; for example, electric lights, electric motors, or large PC monitors. See the

External Devices" section on page 3-4

In some cases, hum may be reduced or eliminated by using a local power cube or power injector.

Note

These environmental and hardware inconsistencies in the locations where Cisco Unified IP Phones are

deployed means that there is not a single headset solution that is optimal for all environments.

Cisco recommends that customers test headsets in their intended environment to determine performance

before making a purchasing decision and deploying en masse.

The Cisco Unified IP Phone 6945 supports wideband headsets.

Note

Cisco Unified IP Phone 6921, 6941, 6945, and 6961 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)

OL-24567-01

Understanding the Cisco Unified IP Phone 6921, 6941, 6945, and 6961 Components

for more information.

for details.

"Adding

"Using

3-3