Digital Home System DHS-LIT-SWP-DHS Manuel d'installation rapide - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel d'installation rapide pour {nom_de_la_catégorie} Digital Home System DHS-LIT-SWP-DHS. Digital Home System DHS-LIT-SWP-DHS 2 pages. Dhs z-wave plug-in switch with energy measuring

Imprimer la page

Mounting

1 | Plug the DHS Z-Wave Plug-In Switch into any compatible power outlet.

Please note: This device is designed for Australia/New Zealand GPO only.

The DHS Z-Wave Plug-In Switch should be installed into any indoor, three-

Prong (Aus Type), 220-240 volt A/C outlet.

2 | Plug a lamp or small appliance into the front of the Plug-In Switch.

3 | The Plug-In Switch is now ready for inclusion into /exclusion from your Z-

Wave network.

Include in or Exclude from Z-Wave network

1 | Make sure your Z-Wave controller within 2-3 meters from the device.

2 | Make sure your Z-Wave controller is in the right operation mode (include

or exclude). Do it accordingly to your Z-Wave controller manual.

3 | Press and hold the button on the DHS Z-Wave Plug-In Switch for about 4

seconds until LED on the switch starts blinking slowly, then release the

button.

4 | Observe the lights on the controller. The orange light will blink rapidly

while inclusion is taking place. Inclusion is complete when the orange

light becomes solid.

5 | If inclusion was successful you'll see new device in your home controller

Interface. Your DHS Z-Wave Plug-In Switch if ready for operations.

Please note: if you can't include DHS Plugin Switch to your compatible Z-

Wave controller in AUS version, then please run the exclusion procedure first

and follow with inclusion procedure again.

LED indication modes

The indicator gives various statuses of the device as follows:

1. Ready for learn mode: Indicator light blinks every second.

2. Learn in progress (add): Indicator light blinks 2 times every second.

3. Learn in progress (remove): Indicator light blinks 3 times every second.

4. Learn mode success: Indicator light is on for second.

5. Learn mode failed: Indicator light blinks 8 times fast.

Installation

Manual control

Press the button once to turn the lamp/appliance ON or OFFf

Remote operation

After successful inclusion DHS Z-Wave Plug-In Switch will be represented in

the home controller interface by the single icon with two buttons ON and

OFF you can use to turn switch ON and OFF.

Configuration

Parameter

Number

1 - Set to Default

(Factory Reset)

2 – Measure

Decimals

3 – Power Limit

The relay auto

switches off

when load is

higher then

4 – Startup with

last known

socket status

if a size is other then given size the frame is ignored totally so

•

configuration values are not changed

Operation

Size

Value

Preset

1 byte*

All values(00 – 255)

170

except for 85 can be

used to reset

1 byte*

0,1,2,3 (decimals in

power report)

2 bytes*

0: no power limit

3600

selected

1 – 2500: variable

power limit

1 byte*

0: When power

applied socket is OFF

1 – 255: When power

applied socket is the

state before power

was disconnected.

Supported Command Classes

Basic type: BASIC_TYPE_ROUTING_SLAVE

Generic type: GENERIC_TYPE_SWITCH_BINARY

Specific type: SPECIFIC_TYPE_POWER_SWITCH_BINARY Listening: TRUE,

Z‐ ‐ ‐ ‐ Wave Lib: 4.51

Troubleshooting

NOTE: Before including the product to your Z-Wave network it is advised to

perform exclusion procedure to reset network settings.

This device is using a radio signal that passes through walls, windows and

doors. The range can be influenced by local conditions such as large

metal objects, house wiring, concrete, furniture, refrigerators, microwaves

and similar items. On average, the indoor range is approximately 12- 30

meters.

Do not expose this product to excessive heat or moisture.

Prevent long term exposure to direct sunlight.

Do not attempt to repair this product. If the product is

damaged or if you are in doubt about the proper operation,

take the product back to the place of purchase.

Do not clean the product with any liquid.

Do not paint.

Frequently Asked Questions

Q: Why does the push button on the switch not work?

A1. Check whether the Protection is enabled or not. If it is, disable the

protection and try again. For more information about disabling the

protection please refer to the supporting command classes (parameter 3).

A2. Check if the DHS Plug-in Switch is completely plugged into the socket.

Q: Where can I see the energy consumption measurement?

A1: The energy consumption measurement can be viewed by the use of a

Z‐Wave controller. You can request the accumulated or instant measured

values by the use of the meter command class.

Q: Why is the energy measurement not working?

A1: A device must be plugged into the socket of the DHS Plug-in Switch.

Please check if you had any device plugged in before checking the

energy measurement.

Q: Why does the indicator light not work?

A1: Check if the DHS Plug-in Switch is fully plugged into a socket. The

indicator light will not work if there is no power supplied to the switch.

A2: The Indicator light is only on when the switch is on. Press the push

button to turn it on.