Samsung UN32C4000PD Manuel d'installation rapide

Parcourez en ligne ou téléchargez le pdf Manuel d'installation rapide pour {nom_de_la_catégorie} Samsung UN32C4000PD. Samsung UN32C4000PD 2 pages. 4000 series led tv
Également pour Samsung UN32C4000PD : Manuel de l'utilisateur (46 pages), Manuel de l'utilisateur (4 pages), (Espagnol) Manual Del Usuario (46 pages), (coréen) Manuel de l'utilisateur (46 pages)

Imprimer la page

Samsung UN32C4000PD Manuel d'installation rapide

Quick Setup Guide

Congratulations on the purchase of your new Samsung TV.

Read this setup guide to get your TV up and running quickly.

1-800-SAMSUNG (1-800-726-7864)

STOP

Samsung Electronics America, Inc.

85 Challenger Road Ridgefield Park, NJ 07660-2112

Please do not return this unit.

Samsung Electronics Canada Inc.

55 Standish Court Mississauga, Ontario L5R 4B2

If you have problems operating your

Call Center hours of operation: Mon-Sun, 9:00 AM -12

TV, call:

AM EST.

1-800-SAMSUNG (1-800-726-7864)

To register this product, visit: www.samsung.com/

For web support please visit:

www.samsung.com/support

Step 1

: Install the Stand

Follow the steps below to connect the TV to the stand.

✎

NOTE

Make sure to distinguish between the front and back of the Stand and

Guide Stand when assembling them.

Make sure that at least two people lift and move the LED TV.

Stand the product up fasten the screws. If you fasten the screws with the

with the LED tv placed down, it may lean to one side.

[

Do not insert your fingers into the stand base slot of the TV when

installing the stand base.

Screws (M4 X L12)

Guide Stand

Connect the Guide Stand to the

Stand

Stand using four screws

(M4 X L12) as shown.

Rear

Fasten two screws (M4 X L8) at

With your TV upright, connect the

position 1, and then fasten three

TV to the Stand as shown.

screws (M4 X L8) at position 2.

Front

Rear

Step 2

: Install the Batteries into the Remote

To install batteries into your remote

control, follow these steps:

1. Lift the cover on the back of

the remote upward as shown

in the figure to the right.

2. Install two AAA batteries.

✎

Make sure to match the

+ and - ends of the batteries to the diagram in the battery compartment.

3. Replace the cover.

Step 3

: Connect Antenna or Cable

VHF/UHF Antenna

Connect Ant In to

Antenna Cable

• Wall cable jack

• VHF/UHF Antenna

• Cable or Satellite box

Ant or Cable Out

Use a 75 ohm (round) cable.

Make sure the AC power cord is plugged in securely to

the wall outlet and the TV.

Step 4

: Connect External Devices

Connecting an AV device (DVD/Blu-ray player, cable/satellite box, etc.)

Use one of the connections below to connect your TV to an external A/V device. We recommend using HDMI for the highest picture quality.

Audio Cable

(Not Supplied)

Video Cable

(Not Supplied)

Top view

Good Connection

Component Cable

Component connection (up to 1080p)

(Not Supplied)

Audio Cable

(Not Supplied)

COMPONENT OUT

AUDIO OUT

Connecting an audio device (Home Theater, etc.)

Connect your TV to your Home Theater or other audio device to enjoy enhanced

Sound quality.

Analog Audio connection

Using an Audio Cable

Audio Cable (Not Supplied)

AUDIO IN

Digital Audio connection

Using an Optical Cable

Optical Cable (Not Supplied)

OPTICAL

Best Connection

HDMI Cable (Not Supplied)

Very Good Connection

Component connection (up to 1080p)

HDMI to DVI Cable (Not Supplied)

DVI OUT

Audio Cable (Not Supplied)

AUDIO OUT

Lowest Quality Connection

Audio/Video connection (480i only)

Using a Component Cable

DVD, Blu-ray player, cable box,

STB satellite receiver, VCR

AUDIO OUT

VIDEO OUT

Device

VIDEO OUT

Connecting a PC

Connect your TV to a PC to use it as a Monitor.

Optical Cable (Not Supplied)

Amplifier / DVD

home theater

Audio Cable

(Not Supplied)

D-Sub Cable

Digital Audio System

(Not Supplied)

Using an EX-Link Cable Connection

Available Devices : External devices that support EX-Link

EX-LINK

Step 5

: Run Plug & Play

When you turn on your TV for the first time, it automatically launches the Plug &

Play function. With Plug & Play, you can select the On Screen Display language,

set the clock mode, and launch the TV's channel memorizing process.

It also displays connection instructions similar to those in this guide.

To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow

buttons on your remote. To make a selection, press the ENTERE button.

To skip a screen, press the

HD connection (up to 1080p)

button on the remote or on the TV. To run Plug & Play, follow these steps:

Using an HDMI Cable

Using your remote control, select

DVD, Blu-ray player, HD Cable Box, HD

the language for the On Screen

STB (Set-Top-Box) satellite receiver

Display (OSD), and then press the

Device

HDMI OUT

ENTERE button.

Select Home Use, and then

press the ENTERE button. If

you select Store Demo, the TV

will reset your picture and audio

Using an HDMI to DVI Cable

settings every 30 minutes.

Select Antenna Source to

Device

memorize. If Antenna Source is

Cable or Auto, you must select

Antenna Source to same type

as your cable system type. After

selecting source, select Search;

then press the ENTERE button

on your remote.

✎

Most cable systems are

Standard(STD) systems, If you are

Using an Audio/Video Cable

not sure about what kind of cable

DVD, Blu-ray player, cable box,

system you have, contact your cable company.

STB satellite receiver, VCR

✎

If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After

Plug & Play is complete, set your TV to Channel 3 or 4, according to the

Device

directions for your cable or satellite box.

The TV memorizes the available

channels. This process can take

up to 45 minutes.

After the TV has memorized the

channels, choose the Clock

HD connection

Mode. Select Auto if you have

a digital channel in your area.

Using an HDMI to DVI Cable

Select Manual if you don't, or if

DVI OUT

you have a cable or satellite box.

When done, press the ENTERE

AUDIO OUT

button.

✎

If you select Manual, the clock

setting screen appears.

Audio Cable (Not Supplied)

Select the daylight savings time

setting: Off or On, and then press

the ENTERE button.

Using an D-Sub Cable

AUDIO OUT

Select the time zone in which

you live, and then press the

PC OUT

ENTERE button.

After the time zone screen, The connection method for best HD screen

quality is displayed. Press Right arrow button on your remote to view each

screen in succession. Press the Blue button to skip this section.

The Enjoy your TV. screen appears. Then press the ENTERE button.

If You Want to Rerun Plug & Play

1. Press the

SOURCE

: Connector for service only.

2. Press the

3. Press the ▲ or ▼ button to select Setup, and then press ENTERE.

4. Press ENTERE again to select Plug & Play.

button. To turn on your TV, press the

POWER

Plug & Play

Select Language of the OSD.

English

Español

Menu Language

Français

U Move E Enter

Plug & Play

Select the usage mode.

Store Demo

Home Use

Previous U Move E Enter

Plug & Play

Anrenna Source

Air

Digital Cable System

Cable

Auto

Analog Cable System

U Move E Enter

Plug & Play

Removing scrambled channel.

DTV Cable

76%

DTV Air

Air

212

DTV Cable

Cable

Stop

E Enter

Plug & Play

Set the Clock Mode.

Auto

Clock Mode

Manual

U Move E Enter

Plug & Play

Set to daylight saving time.

Off

DST

U Move E Enter

button on your remote, then select TV mode.

button on your remote to display the menu.