Siemens SX Series Manuel d'utilisation - Page 10

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Siemens SX Series. Siemens SX Series 42 pages. Dishwasher
Également pour Siemens SX Series : Instructions de fonctionnement (38 pages), Manuel d'utilisation (38 pages), Manuel d'utilisation (42 pages), Manuel d'utilisation (44 pages), Manuel d'utilisation (46 pages), Manuel d'utilisation (44 pages), Manuel d'utilisation (42 pages), Manuel d'instruction (48 pages), Manuel d'utilisation (40 pages), Manuel d'utilisation (42 pages), Manuel d'utilisation (44 pages), Manuel d'utilisation (40 pages)

Imprimer la page
Siemens SX Series Manuel d'utilisation
en

Water softening system/Special salt

Water softening
system/Special salt
s a l t
e m / S p e c i a l
n g s y s t
s o f t e n i
W a t e r
To ensure good washing results,
the dishwasher requires soft water, i.e.
containing low amounts of lime,
otherwise white limescale will be
deposited on the utensils and inner
container.
Tap water above 1.2 mmol/l must be
softened. The water is softened with
special salt (regeneration
salt) in the water softening
system of the dishwasher.
The setting and therefore the required
amount of salt
depends on the degree of hardness of
your tap water (see table).

Setting

The amount of salt dispensed can be
set from
:
to :
Salt is not required at the set value
Salt is not required at the set value
Salt is not required at the set value
:
.
1. Find out about the hardness value of
Find out about the hardness value of
Find out about the hardness value of
your tap water. Your water utility
your tap water. Your water utility
your tap water. Your water utility
company will help you with this.
company will help you with this.
company will help you with this.
2. Set value can be found in the water
Set value can be found in the water
Set value can be found in the water
hardness table.
3. Close the door.
4. Switch on ON/OFF switch (.
Switch on ON/OFF switch
Switch on ON/OFF switch
5. Hold down programme button #
and press START button h until
: .... is indicated on the digital
display.
6. Release both buttons.
The LED for button # flashes and
the digital display )* displays the
factory setting :
10
.
.
To change the setting:
1. Press programme button 3.
Each time the button is pressed, the
set value increases by one level;
when the value of :
reached, the display jumps back
to
:
(off).
2. Press START button h.
The chosen setting has now been
stored.

Water hardness table

:DWHU
+DUGQHVV
+DUGQHVV
+DUGQHVV
KDUGQHVV
UDQJH
YDOXH
ƒ&ODUNH
VRIW
VRIW
VRIW
VRIW
VRIW
VRIW
PHGLXP
PHGLXP
PHGLXP
KDUG
KDUG
KDUG

Using special salt

Always refill with special salt
immediately before switching on the
appliance. This ensures that overrun
special salt solution is immediately
washed out and does not corrode the
rinsing tank.
1. Open the screw-type cap of the
compartment 1R.
2. Fill the tank with water (only required
when switching on the appliance for
the first time).
has been
PPROO
6HW YDOXH
RQ WKH
PDFKLQH
‡¯¯
‡¯³
‡¯›
‡¯´
‡¯ž
‡¯‚
‡¯±
‡¯Å