Ricoh Aficio CL3000 Manuel d'installation rapide - Page 3
Parcourez en ligne ou téléchargez le pdf Manuel d'installation rapide pour {nom_de_la_catégorie} Ricoh Aficio CL3000. Ricoh Aficio CL3000 4 pages. Sap printing
Également pour Ricoh Aficio CL3000 : Manuel (49 pages), Manuel d'installation (3 pages), Manuel complémentaire (3 pages), Manuel des options (48 pages), Manuel complémentaire (38 pages), Manuel (12 pages)
Imprimer la page
Sheet 2/2 (From sheet 1/2)
PRINTING THE TEST PAGE
ADJUSTING THE IMAGE
You can check if the printer works properly by
DENSITY
printing a test page such as the configuration page.
To use the printer in its best condition, adjust the
However, you cannot check the connection
image density.
between the printer and the computer by printing
the test page.
Press the {Menu} key.
Turn on the printer if it is not on yet.
"Menu" appears on the panel display.
Press the { } or {
"Maintenance", and then press the {Enter #} key.
Press the { } or { } key to display "Image
ZHBH740E
Density", and then press the {Enter #} key.
After the machine warms up, "Ready" appears on the panel display.
Ready
The following message appears on the panel display.
Press the {Menu} key.
Menu:
Paper Input
Press the {Enter #} key.
Press the { } or { } key to display "List/Test Print".
The following massage appears on the panel display, and then Press
Menu:
the {Enter #} key.
List/Test Print
Press the {Enter #} key.
The following message appears on the panel display.
List/Test Print:
Config.Page
Compare the colors on the printed image density
Confirm that "Config.Page" is on the display, and
test sheet with those on the Image Density
then press the {Enter #} key.
Adjusting Card.
Press the { } or { } key to select the color you
In a short time, the test printing will start.
want to adjust, and then press the {Enter #} key.
Printing...
Important
If you cannot complete the test printing correctly,
see if an error message appears on the panel
display. For more information about error
messages, see "Troubleshooting" in the
Maintenance Guide.
Press the {On Line} key.
"Ready" appears on the panel display.
Ready
Turn off the printer's power switch.
Press the { } or { } key to set the image density
value, and then press the {Enter #} key.
Black
(-10 +10)
Note
You can adjust the image density from -10 to +10.
Menu:
Increasing the value makes the printouts darker and
Paper Input
decreasing the value makes the printouts lighter.
Pressing the { } or { } key makes the value
increase or decrease by one.
} key to display
To adjust another color, repeat the steps
Print another image density test sheet and check
Menu:
if the colors on the test sheet now match those
Maintenance
on the Image Density Adjusting Card. If they still
do not match, adjust the image density again.
Press the {On Line} key.
"Ready" appears on the panel display.
Maintenance:
Image Density
Ready
Image Density:
Prt.Test Sheet
Prt.Test Sheet:
Press # to Start
Printing...
Image Density
Black
CONNECTING THE PRINTER TO
A COMPUTER
Connecting the printer to a computer using
0
a network interface cable.
If your printer is installed with the Network
Interface Board, follow the procedures below.
Important
The interface cable is not provided with the printer.
It is your responsibility to provide the interface
cable appropriate for the computer that you are
using.
to .
Confirm that the printer's power switch is off. If it
is on, turn it off.
ZHBH730E
Loop the network interface cable and attach the
ferrite core.
Note
Attach two ferrite cores to the network interface
cable. One of them must be attached close to the
end of the cable (on the end closet to the printer).
The other must be attached approximately 45 cm
(18") (A) apart from the end. Attach each ferrite
core with a loop.
ZHBP913E
Connect the network interface cable to the
Ethernet port on the back of the printer.
ZHBH1730E
Connect the other end of the cable to the network
, e.g. hab.
Attach the other end of the parallel cable to the
Turn on the printer.
port of the computer. Secure the cable.
Confirm the LEDs on the Ethernet port.
Turn on the printer and the computer.
Go to
DRIVER".
ZESX338E
is lit when 100 BASE-TX is in use and not lit when 10 BASE-T is
in use.
Connecting the printer to a computer using
is lit when the printer is securely connected to the network.
a USB cable.
Important
Go to
"CONFIGURING THE PRINTER FOR
THE NETWORK".
The interface cable is not provided with the printer.
It is your responsibility to provide the interface
cable appropriate for the computer that you are
using.
Connect the interface cable to the USB2.0
Connecting the printer to a computer using
interface port.
a parallel cable.
Important
The parallel cable is not provided with the printer.
It is your responsibility to provide the parallel cable
appropriate for the computer that you are using.
The printer's parallel connection is a standard bi-
directional interface. It requires a standard 36-pin
parallel cable compliant with IEEE1284 and the
parallel port on the computer.
To avoid electrical interference, use a shielded
cable.
Note
Connect the other end of the interface cable to
Do not use a parallel cable longer than 2.5 meters
the USB interface connector of the computer or
(8.2 feet).
the USB Hub.
Confirm that the printer's power switch is off. If it
is on, turn it off.
Turn the computer off.
Attach the parallel cable to the port of the
printer. Secure the cable with the metal fittings
as shown in the illustration.
Important
Rating voltage of the parallel port for the computer;
Max. DC 5V.
ZHBH010E
"INSTALLING THE PRINTER
ZHBP470E