Ricoh IS760 Manuel d'installation rapide - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel d'installation rapide pour {nom_de_la_catégorie} Ricoh IS760. Ricoh IS760 2 pages. Image scanner

Imprimer la page

Connecting to the Computer

This scanner can be connected to the computer

When you do not use the USB

with a SCSI and/or USB interface.

connection

You can connect the scanner to two computers

at the same time. One with the SCSI interface,

Changing the DIP Switch settings enables high-

and one with the USB 2.0 interface. Though,

you cannot use the scanner at the same time

speed data transfer. This is available with SCSI

from two computers. Interfaces are switched

connection, the USB and the optional IEEE1394

automatically when you change from one of the

connection cannot be used with this setting.

computer to the other.

A Set the DIP Switch NO.2 to the OFF position.

Important

SCSI synchronous transmission is enabled.

❒ The SCSI interface of this unit is of the 50-

pin half-pitch (pin-type) type. Connect a

Set the SCSI ID by rotating the Rotary

shielded SCSI-2 compliant with ANSI stan-

dards or a SCSI-3 (Ultra-SCSI) cable.

Switch.

❒ It is possible that malfunction occurs or data

is lost when more than one SCSI ID's exists

simultaneously. Adjust the settings such that

the SCSI ID of this unit does not coincide

with the ID of another SCSI device.

❒ Keep the total length of the SCSI cable in-

cluding the cable inside the PC to a maxi-

mum of 1.5m (4.9 feet) when using the

SCSI-3 (Ultra-SCSI) and 3m (9.8 feet) when

using the SCSI-2.

❒ Some combinations of the SCSI board of

your computer and daisychained peripherals

might cause an incorrect operation.

Please contact and ask your service

representative about the recommended

SCSI board.

❒ If you connect this unit to other SCSI devices

through a daisy chain, it may not work

Connecting the SCSI Interface

properly. In this case, connect only this

(When the Scanner is not at the End

unit to the computer.

of the Daisy Chain)

Connecting the SCSI Interface

Shut down the computer and all of

(When the Scanner is at the End of

the SCSI connected devices.

the Daisy Chain)

Daisy chain the computer, scanner

Shut down the computer and all of

and SCSI connected devices.

the SCSI connected devices.

Daisy chain the computer, scanner

and SCSI connected devices.

Open the cover of the switch box

on the lower left of the front side of

ADC018S

Note

the scanner.

❒ Connect the SCSI cable to either one side of the

Note

connectors.

❒ Push the knob of the cover to the left and pull

the cover to open.

Open the cover of the switch box

on the lower left of the front side of

the scanner.

Set the DIP Switch NO.3 to the ON

position.

Note

❒ Push the knob of the cover to the left and pull

the cover to open.

Confirm the DIP Switch NO.3 is in

the OFF position.

Built-in SCSI terminator is disabled.

ADC019S

When you do not use the USB

connection

Changing the DIP Switch settings enables high-

speed data transfer. This is available with SCSI

connection, the USB and the optional IEEE1394

connection cannot be used with this setting.

A Set the DIP Switch NO.2 to the OFF position.

SCSI synchronous transmission is enabled.

Set the SCSI ID by rotating the Rotary

Switch.

ADC017S

Connecting the USB Interface

Note

❒ Please use the recommended USB cable. Using

other cables might occur an irregular operation.

As for the recommended cables, please ask your

service representative.

Open the cover of the switch box

on the lower left of the frontside of

the scanner.

Note

❒ Push the knob of the cover to the left and pull

the cover to open.

Confirm the DIP Switch NO.2 is in

the ON position.

ADC020S

ADC080S

Note

❒ If the DIP Switch NO.2 is set to OFF, set it to

ON. The scanner will not be detected if the

switch is set to OFF.

Connect the USB cable to the USB

connector.

ADC021S

ADC022S

Connect the other side of the cable

to the USB connector on your com-

puter.

Connecting the Power Code

Confirm the lock screws on the back

This section explains how to connect this

of this machine are removed and the

machine to a power source, using a bundled

holes left by the removed screws

AC power cord.

are covered with the cap, and con-

firm that the lock lever is set to the

WARNING

"Unlock" position.

• Do not use with a power source with a voltage

different from the specified voltage. Do not use

a power outlet with multiple devices plugged

in. These could create the risk of fire or elec-

tric shock.

• Avoid the use of an extension cord.

• Do not damage, break, twist or modify the

Power Cord. Placing heavy objects on the

cord, pulling on or bending it excessively can

damage the Power Cord, creating the risk of

fire or electric shock.

• Never touch or unplug the power plug with wet

hands. This can create the risk of electric

shock.

❒ Turning the power on leaving the lock lever

to the "Lock" position and/or turning the

power on without removing the screws could

CAUTION

result not only in failure in scanning but in

• When unplugging from an outlet, be sure to

malfunction of this machine.

grasp the plug when pulling. Never pull on

the cord. This could damage the cord creat-

Push the power cord plug all the

ing the risk of fire or electrical shock.

way into the power connector on

this machine.

Confirm that the power switch is set

to off.

Note

❒ Be sure to use the power cord that comes with

ADC124S

this machine.

Insert the power plug into the power

outlet.

Appendix: Turning the Power On/Off

Turning the Power On when

Connected with SCSI Interface

Connected with USB Interface

Turn the power on from the farthest devices from

There is no order to turn on the power when you

the computer on the daisy chain. Start the

connect the scanner with USB Interface. You can

computer last.

turn on either the scanner or the computer first.

Note

❒ The scanner will not be detected if you start the

computer first.

Detecting

the Scanner

Power on the scanner.

Start the computer.

The installation completes here for the

computer with the operation systems, Windows

95 and Windows NT4.0. For the computer with

ADC089S

other operation systems, "Plug & Play" detects

Important

the scanner and the "Found New Hardware

Wizard" automatically starts.

In the Wizard, select [Search for a

suitable driver for my device [rec-

ommended]], and continue the

"Found Ne w Hardware Wizard" to

the end, according to the instruc-

tion on the displa y.

Note

❒ When an instruction to set the Windows system

CD-ROM appears on the display in the course

of the installation, follow the instruction accord-

ingly.

❒ Even when "No approval of the logo test" ap-

pears on the display, you can continue the in-

stallation by clicking [continue].

ADC026S

Turning the Power Off

There is no order to turn off the power. You can

turn off either the scanner or the computer first.

Printed in Japan

EN USA

Quick Installation Guide

ADC125S