Argo ADICS13DC Manuel d'utilisation - Page 7

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Argo ADICS13DC. Argo ADICS13DC 15 pages. Split air conditioner system
Également pour Argo ADICS13DC : Manuel d'instructions d'installation (19 pages), Manuel d'utilisation (17 pages)

Imprimer la page

A U t o M A t I C o P E R A t I o n I n M U L t I S P L I t

ConFIGURAtIon

When the air conditioning system configuration is multisplit

and there is more than one indoor unit connected, the

automatic mode operates as follows:

- the first unit that switches on the system also decides the

operation mode (cooling or heating) for all the other units

that will be switched on after the first one;

- when the system has been switched on in cooling mode

and one unit is activated in heating mode, an error will

be signaled for this unit (wrong operating mode). If the

same unit is switched on in "automatic" mode and the

desired temperature is lower than the detected ambient

temperature, the unit will operate in cooling mode, like the

other units of the system; on the contrary, if the desired

temperature is higher than the detected one, the unit will

operate in fan mode;

- when the system has been switched on in heating mode

and one unit is activated in cooling mode, an error will

be signaled for this unit (wrong operating mode). If the

same unit is switched on in "automatic" mode and the

desired temperature is higher than the detected ambient

temperature, the unit will operate in heating mode, like the

other units of the system; on the contrary, if the desired

temperature is lower than the detected one, the unit will

operate in fan mode.

DEhUMIDIFYInG (DRY)

1. Set the

button to DRY. The icon

2. Press the +/- buttons (temperature selection) to set the

desired temperature (the temperature range is between

32 °C max. and 10 °C min.).

THE DISPLAY SHOWS THE

SELECTED TEMPERATURE.

notE

Use DRY operation when you want to reduce the humidity

in the room.

Dehumidifying operation is adjusted both by the difference

between set temperature and air temperature, and by the

value of relative humidity, detected by the sensor.

During DRY operation, the fan speed is automatically

set (Remote control lamp

overcooling.

Dry operation is not possible if the indoor temperature is

10 °C or less.

When room temperature is above set value, the unit

operates to dehumidificate so efficient as possible.

When room temperature is below set value, the unit will

not stop, it will proceed operating with low power to

dehumificate and, in small spaces, temperature could

drop below the set temperature.

is displayed.

AFTER 5 SECONDS FROM THE

REQUIRED TEMPERATURE SETTING

THE DISPLAY WILL SHOW THE ROOM

TEMPERATURE AGAIN.

is ON) to prevent

FAn onLY

If you want to make air circulate without any temperature

control, press

button until only the

appears on the display.

ADJUStInG thE FAn SPEED

AUtoMAtIC

Simply set the FAN selector to the

automatically controls the fan speed when the AUTO mode

is selected. When the air conditioner starts operating, in

heating or cooling, the fan speed varies according to the

thermal load of the room.

MAnUAL

If you want to manually adjust speed just set the FAN

selector as desired.

High speed

nIGht MoDE / EnERGY SAVInG

This mode enables you to save energy.

1. Set the

2. Press the

button.

3. The

mark appears on the display. Press the

button again to release the function.

What does the nIGht mode mean?

When you select the NIGHT mode, the air conditioner will

modify automatically the set temperature after 60 minutes.

This enables you to save energy without sacrificing your

comfort.

OPERATING MODE

Heating

Cooling and Dry

notA

During the NIGHT mode the internal fan speed is

automatically lowered and reduces the noise.

hIGh PoWER MoDE

When this mode is active the internal fan speed is set

automatically and the air conditioner operates at the

maximum power in the selected operating mode (cooling

or heating).

1. Press the

HIGH POWER button.

3. The

mark appears on the display. Press the button

again to release the function..

notE

During the high power operation the room temperature

could not correspond to the set temperature.

fan symbol

position.The unit

Med. speed

Low speed

selector to cool, dry or heat.

SET TEMPERATURE CHANGE

Lowered by 2 °C

Raised by 1 °C