Argo ADICS13DC Manuel d'utilisation - Page 6

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Argo ADICS13DC. Argo ADICS13DC 17 pages. Split air conditioner system
Également pour Argo ADICS13DC : Manuel d'utilisation (15 pages), Manuel d'instructions d'installation (19 pages)

Imprimer la page
HOW TO SET THE CLOCK
EN
1. Press for a few seconds the Timer button
Press the button
SET
WEEK
F
S
S
M
T
W
T
2. AM or PM starts flashing: use the arrows to choose
AM or PM, then confirm with
The hour indication starts flashing: set the hour with
the arrows, then confirm with
The minutes indication starts flashing: set the
minutes with the arrows, then confirm with
WEEK starts flashing: set the day of the week with
the arrows, then confirm with
3. At this point the procedure is finished: press the
button
to exit the clock menu.

COOLING MODE

1. Turn on the unit with the ON / OFF
button.
2. Press the button
COOLING symbol
the display.
3. Press the buttons
desired temperature (the temperature
range is between 10 °C and 32 °C).
SET
THE DISPLAY SHOWS THE
SELECTED TEMPERATURE
AND THE WORD "SET".
4. Press the button
NOTES
•
If the fan is set in automatic mode and the unit stops
because setpoint is reached, also the fan will stop.
•
If the fan is set in one of the six manual speeds, it will
go on operating at the selected speed, even if the unit
stops due to reaching the setpoint.
•
When the external or internal temperature is too low,
the unit could limit the speed of the compressor or
switch it off for a certain period of time to avoid the
formation of ice on the internal heat exchanger.
.
ARROWS
WEEK
T
S
M
AUTO
SET
WEEK
until the
S
M
T
W
appears on
2
to set the
1
AFTER 5 SECONDS FROM THE
REQUIRED TEMPERATURE
S E T T I N G T H E D I S P L A Y
W I L L S H O W T H E R O O M
TEMPERATURE AGAIN.
to select the fan speed.

HEATING MODE

.
1. Turn on the unit with the ON / OFF
button.
2. Press the button
HEATING symbol
the display.
3. Press the buttons
desired temperature (the temperature
W
T
F
S
range is between 10 °C and 32 °C).
SET
THE DISPLAY SHOWS THE
SELECTED TEMPERATURE
AND THE WORD "SET".
4. Press the button
NOTE
If the unit stops because setpoint is reached, also the fan
will stop.
COLD DRAFT PREVENTION
When starting the unit the fan may stop until the indoor
heat exchanger coil has warmed up sufficiently. This
is because the COLD DRAFT PREVENTION SYSTEM
is operating. During this period, the OPERATION lamp
remains lit (red led).
T
F
S
DEFROSTING OF OUTDOOR UNIT HEAT
3
EXCHANGER
4
When the outdoor temperature is low, frost or ice may
appear on the heat exchanger coil, reducing the heating
performance. When this happens, an appropriate
defrosting cycle of the exchanger is activated. During this
function operation, the fan of the indoor unit stops. Heating
operation restarts after several minutes. (This interval
will vary slightly depending on the room and outdoor
temperature).

AUTOMATIC OPERATION

1. Turn on the unit with the ON / OFF button.
2. Press the button
on the display.
3. Press the buttons
(the temperature range is between 10 °C and 32 °C).
SET
THE DISPLAY SHOWS THE
SELECTED TEMPERATURE
AND THE WORD "SET".
The air conditioner will automatically operate by switching
from heating to cooling operation (or vice versa) in order
to maintain the set temperature.
4. Press the button
6
AUTO
SET
until the
WEEK
S
M
T
appears on
2
to set the
1
AFTER 5 SECONDS FROM THE
REQUIRED TEMPERATURE
S E T T I N G T H E D I S P L A Y
W I L L S H O W T H E R O O M
TEMPERATURE AGAIN.
to select the fan speed.
A
until the AUTO symbol
to set the desired temperature
AFTER 5 SECONDS FROM THE
REQUIRED TEMPERATURE
S E T T I N G T H E D I S P L A Y
W I L L S H O W T H E R O O M
TEMPERATURE AGAIN.
to select the fan speed.
W
T
F
S
3
4
appears