Cisco TelePresence MX300 Manuel de démarrage - Page 26
Parcourez en ligne ou téléchargez le pdf Manuel de démarrage pour {nom_de_la_catégorie} Cisco TelePresence MX300. Cisco TelePresence MX300 46 pages. Telepresence c series
telepresence mx series
telepresence sx series
telepresence ex series
Également pour Cisco TelePresence MX300 : Manuel (2 pages), Manuel de démarrage (42 pages), Manuel de référence rapide (2 pages), Manuel de démarrage rapide (12 pages), Manuel de référence rapide (2 pages), Manuel de dépannage (37 pages)
Imprimer la page
Cisco TelePresence Video Systems
Contents
Configuring H.323 and SIP
(When not set by a provisioning system)
To get online and ready to place and receive calls, your system
must be set up properly. Your system uses either the H.323
protocol or the SIP protocol for video calls.
NOTE:
Contact your system administrator, or service provider,
for information about the network settings.
For networks administered through Cisco TMS (Cisco
TelePresence Management Suite), your Cisco TMS adminis-
trator will help you to get online.
You can find information about administering through Cisco UCM
in the
Administering TC endpoints on CUCM
The diagnostics on your system will indicate if there is a problem
with the H.323 or SIP registering.
NOTE:
H.323. is not available for the SX10.
If you are changing a value setting,
you have to always click
save
to confirm the change.
Back to task overview
D14639.15 Video Systems Getting Started Guide TC7.2, OCTOBER 2014.
Introduction
User interfaces
H.323
If in doubt for any of the parameters below, contact your system
administrator or your service provider.
1. Go to the
Configuration
2. Open the
3. Under
Profile1
the
E164
and the
4. Go to the
If you want the system to obtain the H.323 gatekeeper
guide.
address automatically, select
down list; if you want to enter the address manually, select
Manual.
If set to Manual, enter the gatekeeper
sponding input field.
5. If the H.323 gatekeeper requires authentication, and you
want your system to authenticate itself to the gatekeeper, go
to the
Authentication
drop down list. Then enter the
the corresponding input fields.
Otherwise, select
6. Click the
Home
the H.323 settings.
If you have successfully registered to a Gatekeeper, the
Status
is shown as
If you wish to change the other H.323 settings, check the admin-
istrator guide for your product.
Configuration
Configuration
tab, and select
System
Configuration.
H323
settings from the left sidebar.
heading and the
H323Alias
subheading, enter
ID
number in their respective input fields.
Gatekeeper
subheading.
Auto
in the
Discovery
Address
in the corre-
subheading and select
On
in the
LoginName
and
Password
Off
in the
Mode
drop down list.
tab to see the
System Information
and verify
Registered
in the H323 section.
26
Appendices
SIP
If in doubt for any of the parameters below, contact your system
administrator or your service provider.
1. Go to the
Configuration
tab, and select
2. Open the
SIP
page from the left sidebar.
3. Under the
Profile 1
heading, enter the SIP URI in the
input field, and optionally a display name in the
input field.
Select the preferred transpor t protocol from the
DefaultTransport
drop down list. If you select Auto, the
drop
system first tries to connect using Tls, then TCP, and finally
UDP.
4. Select a proxy type in the
type is Standard.
5. Go to the
Proxy 1
subheading.
If you want the system to obtain the SIP proxy address
Mode
automatically, select
Auto
in
if you want to enter the address manually, select Manual.
If you select Manual, enter the proxy
sponding input field.
6. If the SIP proxy requires authentication, you must enter a
login name and password to authenticate your system. Go
to the
Authentication 1
subheading and enter the
and
Password
in the corresponding input fields.
7. Click the
Home
tab to see the
the SIP settings.
If you have successfully registered to a SIP server, the
Status
is shown as
Registered
If you wish to change the other SIP settings, check the admin-
istrator guide for your product.
Copyright © 2010–2014 Cisco Systems, Inc. All rights reserved.
Getting Started Guide
Contacts
System
Configuration.
URI
DisplayName
Type
drop down list. The default
in the
Discovery
drop down list;
Address
in the corre-
LoginName
System Information
and verify
in the SIP section.