Cisco TelePresence Profile 42 Installation - Page 2

Parcourez en ligne ou téléchargez le pdf Installation pour {nom_de_la_catégorie} Cisco TelePresence Profile 42. Cisco TelePresence Profile 42 2 pages. Telepresence ex, mx, quick set c20, codec c, sx20 quick set, profile series video systems
Également pour Cisco TelePresence Profile 42 : Manuel de démarrage (42 pages)

Imprimer la page

Installing Cisco TelePresence System Profile 42"/55"

Wall mounting the unit

(for wall mount foot module only)

CAUTion:

Due to the size and weight of this

equipment, it is very important that the wall

mount unit is safely installed according to the

installation instructions and that the wall is

able to safely support the product.

It is highly recommended that the wall

mounted system is installed by trained

personnel.

Use the Allen key, which is found in the

foot module box, when fastening the wall

brackets to the bottom module with four

M6×10 screws.

Place the bottom module by the wall, mark

where to fasten the brackets and move

the bottom module away.

noTe:

Use a level to make sure the

system is mounted in an upright position.

Add a spacer between the wall bracket

and the wall if necessary.

Add the suitable fixing

device for the screws

in the wall.

Open the rear door. Locate and connect

the cables which are lead out of the

system at the rear side (the door will not

be accessible when the system is placed

by the wall).

Place the bottom module by the wall and

fasten it to the wall with proper screws.

Cables

Mounting the camera

Connect the RJ45 and HDMI cables to the camera,

see illustration.

RJ45

HDMI

Place the camera on the bracket and slide it towards

the front.

Gently pull the cables down from inside the column to

organize the cables.

Close the top cover.

Unpacking the Monitor box and mounting the monitor to the bottom module

Unpack

the monitor

box.

Lift out to open

the snap lockers.

Lift out to unlock and remove the snap lockers.

Lift up the monitor cover to unpack the

monitor.

Locate the speaker grille.

Carefully lift out the monitor and place it onto

the bottom module. It is recommended to be

two persons for this operation.

Insert the two M8×60 screws through the blue

marked holes in the speaker box.

Tighten the monitor gently to the bottom

module until the monitor cannot be moved

anymore.

Camera cable configuration

PrecisionHD 1080p

Push the camera

RJ45

towards the front.

For countries with 60 Hz current frequency

you must set the PrecisionHD 1080p camera

DIP switch to: 00100.

Connecting the monitor cables

Locate the cables in the bottom module and connect them as

illustrated below.

HDMI cable

Speaker in, 15 pin D-SUB cable

(tighten the screws)

Power cable

Power

HDMI 1

A 级声明 (A Class product declaration)

本产品为 A 级 ITE，在其使用说明，铭牌等显著位置中已包含如下内容的声明

(We declare here that the subject product is A class ITE product, and the

following statement is clearly marked in the user manual or nameplate):

eMC A Class declaration

此为 A 级产品。在生活环境中，该产品可能会造成无线电干扰。在这种

情况下，可能需要用户对干扰采取切实可行的措施。

WARNING:

WARning:

This is a class A product. In a domestic environment

This is a class A product. In a domestic environment this

this product may cause radio interference in which case the user

product may cause radio interference in which case the user may be

may be required to take adequate measures.

required to take adequate measures.

finishing up

声明所在位置 (Position of the Declaration):

Use the level adjustment tool to adjust the height of the system to

make it stable (stand-alone foot module only).

Remove the plastic foil from the monitor.

申请号 (Application No.)：

申请人 (Applicant):

Remove the plastic foil from the monitor frame.

型号

(Model Number)：

Snap on the speaker grille to the front.

Use the supplied cloth to clean the system.

HDMI

leVelling AdJUsTMenT

Place the level adjustment

tool on the foot wheel under

the foot module for height

adjustment.

Seen from above, turn

clockwise to adjust the

height up. Use the opposite

side of the tool and turn

counterclockwise to adjust

down.

Rev. Date

Prep.

Checked Change

Telecom AS

117324 rev.

TANDBERG Aquarius 52"

3D CAD model le 117324

rev. 00E+ is master

Page 2

Camera cables

Open the top cover.

Push the camera cables up

the channel inside the monitor.

The entry to the cable channel

is underneath the monitor. You

can reach it inside the base

at the right hand corner (see

close-up illustration below).

Speaker in

警告

Connecting the system

使用说明 User Manual



铭牌 Nameplate



Open the rear door and lead the cables out the opening at the lower part

of the door. Connect the microphone cables if they are not pre-installed.

Close the rear door carefully. Take care not to shut the cables in the

door.

Place the PC cable and the microphones on the table.

Connect the Ethernet cable.

Connect the power cable (use the provided country specific cable).

Open the front door and turn on the monitor.

签字/盖章 Signature/Stamp:

Follow the instructions in the accompanying Touch 8" installation

guide to connect and initialize the touch interface device.

The system should be up and running in a few minutes.

日期 Date:

Sheet 1 of 1

Processes

Tolerances

Speci cation:

Material

Surface treatment

Type:

European

Manufacturer:

projection

Type number:

Thickness:

Unit:

Dimensions without paint or nish

Color:

Sheet size:

All materials, nishes, and proccesses

Surface:

must comply with the RoHS directives

Glossiness:

Scale:

1:20

Flame class:

Part weight:

85203g

Flame class requirement: -

UL reference:

RJ45

HDMI

Cable channel

entry point

The rear door

Ethernet cable

PC cable

Microphone cables

Power cable