Argo SDIAS8DC Manuel d'utilisation - Page 7

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Argo SDIAS8DC. Argo SDIAS8DC 17 pages. Split air conditioner system
Également pour Argo SDIAS8DC : Manuel d'utilisation (15 pages), Manuel d'instructions d'installation (19 pages)

Imprimer la page
Example of operation diagram in the
with the set room temperature at 23°C.
27
A
26
25
B
24
C
23
C
22
21
B
20
A
19
Δ 1 H
ON
MIN.
NOTE
The air conditioner changes the operation mode (from cool
to heat or vice versa, if one of the following conditions
occurs:
- ZONE A: changes if the difference between the room
temperature and the temperature set on the remote
control unit is at least 3°C..
- ZONE B: changes if the difference between the room
temperature and the temperature set on the remote
control unit is at least 1°C, one hour after the compressor
stop.
- ZONE C: never changes if the difference between the
room temperature and the temperature set on the remote
control unit is no more than 1°C.
A U T O M A T I C O P E R A T I O N I N M U L T I S P L I T
CONFIGURATION
When the air conditioning system configuration is multisplit
and there is more than one indoor unit connected, the
automatic mode operates as follows:
- the first unit that switches on the system also decides the
operation mode (cooling or heating) for all the other units
that will be switched on after the first one;
- when the system has been switched on in cooling mode
and one unit is activated in heating mode, an error will
be signaled for this unit (wrong operating mode). If the
same unit is switched on in "automatic" mode and the
desired temperature is lower than the detected ambient
temperature, the unit will operate in cooling mode, like the
other units of the system; on the contrary, if the desired
temperature is higher than the detected one, the unit will
operate in fan mode;
- when the system has been switched on in heating mode
and one unit is activated in cooling mode, an error will
be signaled for this unit (wrong operating mode). If the
same unit is switched on in "automatic" mode and the
desired temperature is higher than the detected ambient
temperature, the unit will operate in heating mode, like the
other units of the system; on the contrary, if the desired
temperature is lower than the detected one, the unit will
operate in fan mode.

DEHUMIDIFYING MODE (DRY)

1. Turn on the unit with the ON / OFF button
2. Press the button
until the DEHUMIDIFYING symbol
appears on the display
3. Press the buttons
(the temperature range is between 10 °C and 32 °C).
SET
THE DISPLAY SHOWS THE
SELECTED TEMPERATURE
AND THE WORD "SET".
(Auto) mode
A
Δ 1 H
ON
ON
MAX.
.
to set the desired temperature
AFTER 5 SECONDS FROM THE
REQUIRED TEMPERATURE
S E T T I N G T H E D I S P L A Y
W I L L S H O W T H E R O O M
TEMPERATURE AGAIN.
NOTES
• Use DRY operation when you want to reduce the
humidity in the room.
• Once the room temperature reaches the set level, the
unit repeats the cycle of turning on / off automatically.
• During DRY operation, the fan speed is automatically
set (Remote control lamp
dehumidification.
• When the room temperature drops below the set
temperature, the unit still continues to operate at a low
temperature and could therefore further reduce the room
temperature in small rooms.
• Dry operation is not possible if the indoor temperature
is less than 10 °C.

FAN ONLY MODE

If you want to make air circulate without any temperature
control, press the button
appears on the display

ADJUSTING THE FAN SPEED

AUTOMATIC
Set with the button
AUTO
. The unit automatically controls the fan speed.
When the air conditioner starts operating, the fan speed
varies according to the thermal load of the room .
NOTE
In FAN ONLY mode, the AUTOMATIC speed corresponds
to the high speed H.
MANUALE
If you want to manually adjust the fan speed just set the
button
as desired:
AUTO
VH
L
Low
ML
Medium-low
M
Medium

NIGHT MODE

This program is used to increase silence and comfort during
the night.
To activate the Night mode:
1. Press the button
dehumidifying or heating.
2. Press the button
3. The symbol
appears on the display. Press the
button again to release the function.
7
AUTO
is ON) to maximize
until the FAN symbol
.
the "AUTO" position
L
ML
H
MH
MH
Medium-high
H
High
VH
Very high
to set the air conditioner in cooling,
.
EN
M