Sony XCG-CG160 Manuel - Page 5

Parcourez en ligne ou téléchargez le pdf Manuel pour {nom_de_la_catégorie} Sony XCG-CG160. Sony XCG-CG160 9 pages. Digital video camera
Également pour Sony XCG-CG160 : Manuel (9 pages)

Imprimer la page

Location and Function of Parts and Controls

➀

Lens mount (C-mount)

Attach any C-mount lens or other optical equipment.

Note

Use a C-mount lens with a protrusion (a) extending from the lens

mount face (b) of 10 mm (13/32 inch) or less.

➁

Guide screw holes (Top)

➂

Guide screw holes/Tripod screw holes (bottom)

When using a tripod, use these four screw holes to attach

a VCT-333I tripod adaptor.

➃

Reference screw holes (bottom)

These precision screw holes are for locking the camera

module. Locking the camera module into these holes

secures the optical axis alignment.

Rear Panel/Pin Assignments

➄

DC IN (DC power input) connector (6-pin)

You can connect a camera cable to input the +12 V DC power

supply. The pin configuration of this connector is as follows.

(Refer to Fig. 6 above for the pin assignment of the

Pin No.

Signal

DC input

(10.5 V to 15 V)

GPI1 (ISO +)

GPI2/GPO2

* only XCG-CG160/CG160C/CG40

RJ45 connector

➅

You can connect a LAN cable to this connector to control the

camera module from a host device to output image to a host

device. By using a PoE-compatible LAN cable and camera

module interface board or hub, you can supply power using the

LAN cable.

Note

For safety, do not connect the connector for peripheral device

wiring that might have excessive voltage to this port.

Reset switch

➆

The camera can be reset to the factory setting by pressing the

reset switch for more than 3 seconds while the power is turned

on.

➇

Status LED (Green)

This button is lit when power is being supplied to the camera.

Various settings linked with GPO are available, such as to light

up when interlocking with the trigger signal.

This button blinks when the network is disconnected, or while 1P

is being acquired.

➀

➁

➂

➃

➅

➆

➇

connector.)

Pin No.

Signal

GPI3/GPO3

(GPO3 (ISO +)*)

GPI1 (ISO –)

GND

Connecting the Cables

Connect the camera cable to the DC IN connector and connect the

LAN cable to the RJ45 connector respectively. If you use a camera

module interface board or a hub that supports PoE, you can

operate the camera even if you do not connect the camera cable

to the DC IN connector. When you connect the LAN cable with

fastening screws, turn the two screws on the connector to secure

the cable tightly.

Connect the other end of the camera cable to the DC-700/700CE

and the other end of the LAN cable to the camera module interface

board or a hub.

➀

RJ45 connector

➁

DC IN connector

➃

➄

Fastening screws

Camera cable

Note

Do not supply power to the camera cable and LAN cable

at the same time.

Controlling the Camera From the Host Device

Control functions

Operating mode

Free run

Trigger edge

Shutter speed

detection

Trigger pulse

width detection

Gain

Partial Scan

(the number of settable lines are 16 or more)

LUT (Look Up Table)

External trigger input

Monochrome model: Mono 8 / 10 / 12 bit

Video output switch

Color model: Raw 8 /10 /12 bit, RGB24 bit,

Defect correction

Shading correction*

Image flip

Area gain

* except XCG-CG40

XCG-CG510/CG510C/CG240/CG240C/CG160/CG160C/CG40

➂

LAN cable

Description

Free run/Trigger

1/40,000 s to 60 s (CG240)

1/100,000 s to 60 s (CG510/CG160/CG40)

1/40,000 s to 60 s (CG240)

1/100,000 s to 60 s (CG510/CG160/CG40)

Setting by trigger pulse width

0 dB to 18 dB

Variable, 4-line increments

OFF/ON (Mode: 5 types)

DC IN connector

YUV24 bit, YUV16 bit

OFF/ON