Sony SS-ZX8 Manuel d'utilisation - Page 36

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Sony SS-ZX8. Sony SS-ZX8 48 pages. Sony operating instructions compact hi-fi stereo system fst-zx8, fst-zx6, lbt-zx8, lbt-zx6

Imprimer la page

Troubleshooting

Problems and remedies

Should you encounter a problem with your

system, do the following:

Make sure the power cord and speaker

cords are correctly and firmly connected.

Find your problem in the troubleshooting

checklist below and take the indicated

corrective action.

If the problem persists after doing all of the

above, consult your nearest Sony dealer.

When the ?/1 indicator flashes

Immediately unplug the power cord and check

the following items.

• Is the voltage selector set to the correct

voltage? Check the voltage for your region,

then make sure the voltage selector is set

correctly.

• Are the + and – speaker cords short-circuited?

• Are you using only the prescribed speakers?

• Is anything blocking the ventilation holes on

the rear of the system?

After checking the above items and fixing any

problems, connect the power cord again and turn

on the system. If the ?/1 indicator still flashes,

or if the cause of the problem cannot be found

even after checking all the above items, consult

your nearest Sony dealer.

General

The display starts flashing as soon as you

plug in the power cord even though you have

not turned on the power.

• The demonstration mode started. Press ?/1 (see

step 5 of "Hooking up the system" on page 8).

The clock/timer setting is canceled.

• The power cord is disconnected or a power failure

occurs. Redo "Setting the clock" (page 11). If you

have set the timer, redo "Waking up to music"

(page 27) and "Timer recording radio programs"

(page 28).

The radio presetting is canceled.

• The power cord is disconnected or a power failure

occurs for longer than half a day. Redo "Presetting

radio stations" (page 16).

There is no sound.

• Turn VOLUME +/– clockwise or press

VOLUME + on the remote.

• The headphones are connected to the PHONES

jack.

• There is no audio output during Timer Recording.

• The tape is in AMS operation during "TAPE A" or

"TAPE B" function.

• Check the Multi Room setting (see "Listening to

the sound in another room" on page 25).

"--:--" appears in the display.

• A power failure has occurred. Set the clock

(page 11) and timer settings (pages 27 – 29) again.

There is no microphone sound.

• Turn VOLUME +/– (or press VOLUME + or – on

the remote) or MIC LEVEL to adjust the

microphone volume.

• Make sure the microphone is connected to the

MIC 1 or MIC 2 jack correctly.

• The tape is in AMS operation during "TAPE A" or

"TAPE B" function.

Sound comes from one channel, or

unbalanced left and right volume.

• Place the speakers as symmetrically as possible.

• Check that the speakers are connected securely

and correctly.

• Turn off the X-ROUND effect (page 24).

Sound lacks bass.

• Check that the speaker's + and – terminals are

connected correctly.

There is severe hum or noise.

• A TV or VCR is placed too close to the system.

Move the system away from the TV or VCR.

• Move the system away from the source of noise.

• Connect the system to a different wall outlet.

• Install a noise filter (commercially available) to

the power cord.

The sound from the component connected to

the VIDEO/MD IN L/R jacks is distorted.

• If "VIDEO" appears in the display when you press

FUNCTION repeatedly, switch to "MD" function

(see "Listening to audio from a connected

component" on page 34).

The timer cannot be set.

• Set the clock again (page 11).