Sony STR-NX3 Manuel d'entretien - Page 8
Parcourez en ligne ou téléchargez le pdf Manuel d'entretien pour {nom_de_la_catégorie} Sony STR-NX3. Sony STR-NX3 42 pages. Tuner/amplifier
Également pour Sony STR-NX3 : Manuel d'entretien (8 pages)
Imprimer la page
[CD Delivery Mode]
• Execute only if connected to the HTC-NX1.
• This mode moves the optical pick-up to the position durable to
vibration. Use this mode when returning the set to the customer
after repair.
Procedure:
1. Press the
?/1
button to turn the power ON.
[ENTER]
2. Press the
and
?/1
3. A message "LOCK" is displayed on the liquid crystal display,
and the CD delivery mode is set.
[Change-over the MW Tuning Interval]
(EXCEPT AEP and UK models)
• The MW tuning interval can be changed over 9 kHz or 10 kHz.
Procedure:
1. Press the
button to turn the power ON.
?/1
[TUNER]
2. Press the
button to select the function "TUNER",
[TUNER BAND]
and press the
3. Press the
button to turn the power OFF.
?/1
[TUNER MEMORY]
4. Press the
and the display on the liquid crystal display changes to "MW
9 k STEP" or "MW 10 k STEP", and thus the tuning interval
is changed over.
[MC Cold Reset]
• The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning
the set to the customer.
Procedure:
1. Turn the power ON or set to the DEMO mode.
[GROOVE]
2. Press the
and
3. The set is reset, and displays "COLD RESET", then becomes
DEMO mode.
[Amplifier Test Mode]
Procedure:
1. Press the
button to turn the power ON.
?/1
2. Press three buttons of
[TUNER BAND]
simultaneously.
3. "ALC OFF" is displayed, then the function which was set be-
fore the test mode became active is displayed.
[LED and Liquid Crystal Display All Lit, Software Ver-
sion Display, Key Check, VACS Level Display Mode]
Procedure:
1. Press the
button to turn the power ON.
?/1
2. Press three buttons of
[STEREO/MONO]
simultaneously.
3. LEDs and liquid crystal display are all turned on.
Rotating the JOG dial changes over the check patterns of liq-
uid crystal display.
4. Successively, the following three modes can be activated.
[VIDEO/DVD]
(1) Press the
displayed on the liquid crystal display.
[MD]
(2) Press the
button, and the key check mode is activated.
In the key check mode, the liquid crystal display displays "K
0 J0 V0". Each time a button is pressed, "K" value increases.
However, once a button is pressed, it is no longer taken into
account.
"J" value increases like 1, 2, 3 ... if turn the JOG dial clock-
wise, or it decreases like 0, 9, 8 ... if turn the JOG dial counter-
clockwise.
"V" value increases like 1, 2, 3 ... if turn the
clockwise, or it decreases like 0, 9, 8 ... if turn the JOG dial
counterclockwise.
[TAPE]
(3) Press the
button, and the VACS level is displayed on
the liquid crystal display.
8
TEST MODE
buttons simultaneously.
button to select the BAND "MW".
and
buttons simultaneously,
?/1
buttons simultaneously.
?/1
[ENTER]
[DISPLAY]
,
[ENTER]
[DISPLAY]
,
button, and the software version is
[VOLUME]
SECTION 4
5. To release from these mode, press three buttons in the same
manner as step 2, or remove the power cord.
[MC Hot Reset]
• This mode resets the set with the preset data kept stored in the
memory. The hot reset mode functions same as if the power
cord is plugged in and out.
Procedure:
1. Turn the power ON or set to the DEMO mode.
2. Press three buttons of
[TUNER MEMORY]
3. The set is reset, and becomes standby state.
[Change-over of VACS ON/OFF]
Procedure:
1. Press the
?/1
2. Press three buttons of
simultaneously, and the display on the liquid crystal display
changes to "VACS ON" or "VACS OFF", and thus the VACS
ON/OFF is changed over.
[VIDEO input, Record and CD play in CD function]
• Execute only if connected to the HTC-NX1.
Procedure:
1. Press the
?/1
2. Press three buttons of
- m simultaneously.
3. "DVD 5.1CH" is displayed on liquid crystal display, and at
the same time, CD is played and the deck B is placed in the
record status.
[CD Service Mode]
• Execute only if connected to the HTC-NX1.
• This mode can run the CD sled motor optionally. Use this mode,
for instance, when cleaning the optical pick-up.
Procedure:
1. Press the
?/1
[CD]
, and
2. Press the
3. Press three buttons of
[STEREO/MONO]
and
4. Set to the Sled Servo mode.
5. With the CD in stop status, turn the JOG dial clockwise to
move the optical pick-up to outside track, or turn it counter-
clockwise to inside track.
6. To release from this mode, perform as follows.
1) Move the optical pick-up to the most inside track.
, and
2) Remove the power cord.
Notes: • Always move the optical pick-up to most inside track when
releasing from this mode. Otherwise, a disc will not be un-
loaded.
• Do not run the sled motor excessively, otherwise the gear can
be chipped.
dial
[ENTER]
[DISPLAY]
,
simultaneously.
button to turn the power ON.
[ENTER]
[DISPLAY]
,
, and
button to turn the power ON.
[ENTER]
[DISPLAY]
,
button to turn the power ON.
button to select the function "CD".
[ENTER]
[POWER SAVE/DEMO]
,
simultaneously.
, and
[GROOVE]
, and
,