Sony WX-850BT Manuel d'utilisation - Page 19

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Sony WX-850BT. Sony WX-850BT 35 pages. Bluetooth audio system

Imprimer la page

POSITION (listening position)

F/R POS (front/rear position)

Simulates a natural sound field by delaying the

sound output from speakers to suit your

position:

 [FRONT L] (front left),

 [FRONT R] (front right),

 [FRONT] (center front),

 [ALL] (center of your car),

[CUSTOM] (position set by the advanced car

audio settings on SongPal)

[OFF] (no position set)

ADJ POSITION (adjust position)

Fine-tunes the listening position setting: [+3] –

[CENTER] – [-3].

(Available only when [F/R POS] is not set to [OFF]

or [CUSTOM].)

SW POS* (subwoofer position)

 [NEAR] (near),

 [NORMAL] (normal),

 [FAR] (far)

DSO (dynamic stage organizer)

Creates a more ambient sound as if there were

speakers in the dashboard: [OFF], [LOW], [MID],

[HIGH].

BALANCE

Adjusts the sound balance: [RIGHT-15] –

[CENTER] – [LEFT-15].

FADER

Adjusts the relative level: [FRONT-15] – [CENTER]

– [REAR-15].

DSEE (digital sound enhancement engine)

Improves digitally compressed sound by

restoring high frequencies lost in the

compression process.

This setting can be memorized for each source

other than the tuner.

Selects the DSEE mode: [ON], [OFF].

AAV (advanced auto volume)

Adjusts the playback volume level of all

playback sources to the optimum level: [ON],

[OFF].

RB ENH (rear bass enhancer)

Rear Bass Enhancer enhances the bass sound by

applying a low pass filter setting to the rear

speakers. This function allows the rear speakers

to work as a subwoofer if one is not connected.

(Available only when [SW DIREC] is set to [OFF].)

RBE MODE (rear bass enhancer mode)

Selects the rear bass enhancer mode: [1], [2], [3],

[OFF].

LPF FREQ (low pass filter frequency)

Selects the subwoofer cut-off frequency: [50Hz],

[60Hz], [80Hz], [100Hz], [120Hz].

LPF SLOP (low pass filter slope)

Selects the LPF slope: [1], [2], [3].

SW DIREC (subwoofer direct connection)

You can use the subwoofer without a power

amplifier when it is connected to the rear

speaker lead.

(Available only when [RBE MODE] is set to [OFF].)

Be sure to connect a 4 – 8 ohm subwoofer to

either of the rear speaker leads. Do not connect

a speaker to the other rear speaker lead.

SW MODE (subwoofer mode)

Selects the subwoofer mode: [1], [2], [3], [OFF].

SW PHASE (subwoofer phase)

Selects the subwoofer phase: [NORM], [REV].

SW POS* (subwoofer position)

Selects the subwoofer position: [NEAR],

[NORMAL], [FAR].

LPF FREQ (low pass filter frequency)

Selects the subwoofer cut-off frequency: [50Hz],

[60Hz], [80Hz], [100Hz], [120Hz].

LPF SLOP (low pass filter slope)

Selects the LPF slope: [1], [2], [3].

S.WOOFER (subwoofer)

SW LEVEL (subwoofer level)

Adjusts the subwoofer volume level:

[+10 dB] – [0 dB] – [-10 dB].

([ATT] is displayed at the lowest setting.)

SW PHASE (subwoofer phase)

Selects the subwoofer phase: [NORM], [REV].

SW POS* (subwoofer position)

Selects the subwoofer position: [NEAR],

[NORMAL], [FAR].

LPF FREQ (low pass filter frequency)

Selects the subwoofer cut-off frequency: [50Hz],

[60Hz], [80Hz], [100Hz], [120Hz].

LPF SLOP (low pass filter slope)

Selects the LPF slope: [1], [2], [3].

HPF (high pass filter)

HPF FREQ (high pass filter frequency)

Selects the front/rear speaker cut-off frequency:

[OFF], [50Hz], [60Hz], [80Hz], [100Hz], [120Hz].

HPF SLOP (high pass filter slope)

Selects the HPF slope (effective only when [HPF

FREQ] is set to other than [OFF]): [1], [2], [3].

AUX VOL (AUX volume level)

Adjusts the volume level for each connected

auxiliary device: [+18 dB] – [0 dB] – [-8 dB].

This setting negates the need to adjust the

volume level between sources.