Acuity Brands Aculux AX3 A WDTW Instructions d'installation - Page 4

Parcourez en ligne ou téléchargez le pdf Instructions d'installation pour {nom_de_la_catégorie} Acuity Brands Aculux AX3 A WDTW. Acuity Brands Aculux AX3 A WDTW 5 pages. Dmx512 / rdm field

Imprimer la page

DMX Downlight Installation

1. DMX Cable needs to meet the ANSI/TIA/EIA-485 standard for DMX-512 and have nominal characteristic impedance of 120 Ohms.

2. Termination resistors are included with each luminaire and should remain installed in the last luminaire of each run to prevent erratic network behavior.

3. No more than 30 fixtures may be installed on a single run.

4. No more than 1000 ft. of wire may be installed on a single run.

5. No T-TAPS, STARS (except by a DMX/RDM splitter), splices, or Ys allowed.

6. All fixtures intended to be controlled as a zone should be given the same DMX start address. Fixtures default to a start address of 1.

7. The following RDM configuration devices are recommended for fixture addressing and configuration

a) Acuity Controls Fresco DXT-1M12-2M09-NE1L and Pathport Manager 5.3 software

b) Fresco FCS7TSNX

DMX Installation Guide

Commissioning with Remote Device Manage (RDM)

After the fixtures are properly wired together as a DMX network (also known as a DMX universe):

1. Use an RDM controller (such as Fresco) that is compliant with ANSI E1.20 - 2010 Entertainment Technology RDM

Remote Device Management Over DMX512 Networks requirements.

2. Set the address(s) for the fixture(s) (addresses are also known as slots).

3. Do not use other personalities before consulting with factory.

4. After commissioning, do not operate the system with RDM and DMX messages at the same time.

Table 1:

Supported RDM PIDs

DMX-RDM PIDs

Standard PID definition

Disc_Unique_Branch

Disc_Mute

Disc_Un_Mute

Supported_Parameters

Parameter_Description

Device_Info

Software_Version_Label

DMX_Start_Address

Identify_Device

Device_Model_Description

Manufacturer_Label

Device_Label

DMX_Personality

DMX_Personality_Description

Curve

Curve_Description

Table 2:

For TW/BBD Aculux only:

Please use personality 2 for Black Body Dimming (BBD), also known as Warm Dimming, or personality 5

for Tunable White (CCT Tuning). Consult with factory before using other personalities.

DMX-RDM

Personality

Personalities

Item

Warm Dimming

3000K SQ

Tunable White

4300K SQ

Product Services Phone (888) 387-2212

1300 S. Wolf Road • Des Plaines, IL 60018 • Phone 800-323-5068 • Visit us at www.acuitybrands.com/aculux

Req

Get

Set

Yes

Slots

Slot 1 Handle

Brightness

Rev 3/17

INSTALLATION INSTRUCTIONS

Aculux

PID Implementation

Aculux

Acuity Brands

Settable

N/A

Logarithmic and Linear,

Preset to Logarithmic

See note above

Slot 2 Handle

Description

n.a.

BBD 1800-3000K,

square law response

CCT

CCT tuning 2000-4350K,

square law response

P6160

Aculux Tunable White/BBD

PID Implementation

Aculux BBD and Tunable White

Juno Lighting Group

Aculux IC/TC410T(SQ)

See Table of Personalities

N/A

4 of 5