Argos Manhattaan 432/5114 Instructions d'assemblage et de montage - Page 3
Parcourez en ligne ou téléchargez le pdf Instructions d'assemblage et de montage pour {nom_de_la_catégorie} Argos Manhattaan 432/5114. Argos Manhattaan 432/5114 4 pages. Clear sat nickel rc ceiling fan
FIGURE 5
BLADE
SCREW &
SPRING WASHER
LAMP
HOLDER
SCREW &
SPRING WASHER
FIGURE 6
LAMP HOLDER
LAMP SHADE
PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
ASSEMBLY OF THE FAN BLADES AND LAMP HOLDER
1.Install the fan blades sets onto motor by tightening the hexagonal screws and spring washers.
2. Secure the lamp holder onto the lamp holder bracket by tightening the 3 set screws.
(CAUTION: Make sure the set screws are fitted properly into the key slots.)(Figure 5)
Attention: Ensure the star washers to be secured tightly to lamp gallery bracket with sot screws.
REMOTE CONTROL
-Use the remote control transmitter to change the speed of the fan and to switch the light and fan
on or off.
-Replace the batteries by sliding the battery compartment cover on the romote control transmitter
in the direction of the arow,fit 2*AAA batteries ,ensure the polarity of the batteries match wit the
figures shown in the battery compartment .(Note:Batteries NOT include). Reassemble the battery
compartment cover.
INFRARED
-Always ensure the battery compartment cover is closed properly.
RAY RECEIVER
-Don'ts expose the remote control to direct sunlight
-Don'ts attempt to rechange expired bateries. There are special rechargeable batteries,which are
clearly marked with.
-Don'ts dispose of batteries in fire to avoid explosion.
REVERSE CONTROL
The fan must be switched off before this slide switch, located on the side of the switch housing is
operated.
Switch upwards for REVERSE winter operation.
Switch downwards for FORWARD summer operation.
FITTING THE LIGHT
1. Insert 40W E14 bulb (not supplied) into the lampholders. Do not use a higher wattage bulb.
2. Install the lamp shade onto the lamp holder by rotating the lamp shade clockwise.
3. The light is switched on and off by the use of remote control.(Figure 6).
CLEANING
FAN MOTOR
HOUSING
Wipe with a soft dry cloth or use a soft brush to remove dust. Care should be taken that no water
or moisture gets into the ceiling fan. Do not use water to clean the ceiling fan.
Do not use metal polish or abrasive cleaning materials on any part. A small amount of furniture
polish can be used to clean the fan blades. When cleaning the fan blades do not apply too much
pressure on them. It is recommended that you support the ends of the blades when you clean
them.
TROUBLE SHOOTING
Fan will not start
CAUTION: Make sure mains power is switched off before you carry out these checks.
1. Check the main and branch circuit fuses or contact breakers.
2. Check power supply wires to the fan are secure.
3. Check reverse switch is firmly in the up or down position.
Fan sounds noisy
Allow a break-in period of 24 hours. Most noise associated with a new fan will disappear after
this period.
1. Check to make sure all screws to the fan motor housing are secure but not overtight.
FAN MOTOR
2. Check mounting plate screws are tight and securely fitted to ceiling joist or ceiling support.
HOUSING
3. Check that the screws which attach the blade holder arms are tight.
4. Make sure the screws securing the lamp shade are finger tight. Check that the lamp is properly
fitted to the lampholder.
5. A dimmer switch should not be fitted to this ceiling fan. If this ceiling fan is connected to a dim-
mer switch it will make noises when the fan light is switched off. Remove the dimmer switch.
Fan wobblers or shakes excessively.
Please note that a small amount of wobble is natural and should not be considered a problem.
All blades are weighed and grouped by weight. Natural wood varies in density which could
cause the fan to wobble even though all blades are weight matched. The following procedure
should eliminate most of the wobble. Check for wobble after each step.
1. Check that fan blades are screwed firmly into the blade holder arms.
2. Check that all blade holder arms are tightened securely to the fan housing.
3. Most fan wobble problems are caused when blade tracking levels are unequal. Blade tracking
may be checked simply by use of a length of timber. Place the timber vertically against the ceiling
and even with the outside leading edge of the blade. Mark the distance from the edge of the
blade to the ceiling. Turn the blades slowly by hand to check the remaining blades. If a blade is
not in alignment, the blade holder arm may be gently bent up or down to be in-line with the other
blades. Allow the fan to operate for ten minutes to check if this problem has been solved.
4. Make sure the mounting plate is securely fixed to the ceiling joist.
5. Check that the ball joint engages with the groove on the ceiling canopy.
2