Motorola CLP1010 Référence rapide

Parcourez en ligne ou téléchargez le pdf Référence rapide pour {nom_de_la_catégorie} Motorola CLP1010. Motorola CLP1010 2 pages. Clp series two-way radio
Également pour Motorola CLP1010 : Manuel de l'utilisateur (48 pages)

Imprimer la page

QUICK REFERENCE

CLP SERIES™ TWO-WAY RADIO

Power Battery

Button

Volume

Control (+/-)

Congratulations on your new radio!

Your radio is ready for use after a fully-charged battery has been installed and it is connected to an

appropriate audio accessory. Please refer to www.motorolasolutions.com/CLP for information on

approved accessories.

CLP Series business two-way radios operate on radio frequencies that are regulated by the Federal

Communications Commission (FCC). In order to transmit on these frequencies, you are required to

have a license issued by the FCC. http://www.fcc.gov

This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this

device does not cause harmful interference.

GETTING STARTED

INSTALL THE BATTERY

•

Push up the latch at the bottom of the battery door and lift the battery door off the radio.

•

Align the battery contacts with tabs in the battery compartment. Insert the contact side of the

battery first, then press the battery down to secure in place.

•

Put the battery door back on the radio. Push down the latch to lock.

CHARGE THE BATTERY

•

Connect the power supply to the drop-in charging tray or multi-unit charger and insert the radio into

the tray. The light on the charger is red when the radio is charging. It turns to green once the radio

is fully charged.

CONNECT AN AUDIO ACCESSORY

•

Connect a wired audio accessory or pair with a wireless accessory (selected models only).

Accessory

Connector

Menu Button

Smart Status

Glow

Push-to-Talk

(PTT) Button

TURN THE RADIO ON

•

Press and hold the Power/Battery button until you hear a short tone and the Smart Status Glow

lights up. (To turn off, press and hold the button until you hear a short tone and the Smart Status

Glow indicator flashes once.)

CHECK THE BATTERY STATUS

•

When powered on, short press and release the Power/Battery button, the Smart Status Glow and

Voice Assisted Operation* features will give you the battery status.

•

Green – high level

•

Yellow – medium level

•

Red – low level

•

Red blink – critical

•

After the Smart Status Glow and Voice Assisted Operation* features indicate the BATTERY

STATUS, it will return to the current channel color.

•

* Voice-Assisted Operation may not be available on certain previous shipping radios

TRANSMITTING AND RECEIVING

Turn radio on and set volume level by pressing volume control +/- buttons. A total of 16 volume

levels are available. (*) To quickly lower the headset volume, press and hold + or - button while

receiving audio. To switch back to the previous headset volume setting, press and hold + or -

button again.

To talk, press and hold the PTT button on the front of the radio (or on selected wired audio

accessories with an inline PTT). Speak clearly into the microphone on the audio accessory. When

finished talking, release the PTT to listen.

To receive, listen through the earpiece at the volume level you have set. Press the PTT to respond.

Note:

(*) Enhancement feature on CLP radios. May not available on previous shipping radios. CLP Series radios always

require the use of an audio accessory with microphone and speaker. Make sure to have the earpiece portion of the

accessory on ear before turning radio on and doing any feature changes.

OPERATION WITH MENU SETTINGS

Press Menu button to navigate through the Menu settings. Voice Assisted Operation feature may not be

available on certain previous shipping radios. At any time in Menu mode, short press PTT or wait 3

seconds to exit the menu.

HOW TO...

Change Channel

Press Menu button to navigate to Channel.

Enter Monitor mode

Press Menu button to navigate to Monitor.

Enter Scan mode

Press Menu button to navigate to Scan.

Send Call Tome (enable

Press Menu button to navigate to Call Tone.

through CPS)

Quick Tip: It is not necessary to wait for the voice prompt to be completed before continuing with next button press.

Note:

For single channel models, monitor, scan mode and call tone are supported. Single channel models support scan

mode when the user enables "dynamic talkaround scan" on a repeater channel via the customer programming

software.

For further information, refer to your specific product User Guide. For product-related questions, please

call: 1-800-448-6686 (USA), 1-800-461-4575 (Canada) or visit www.motorolasolutions.com/CLP.

ATTENTION

Before using this product, read the RF energy awareness information and operating instructions

contained in the Safety and RF Energy Exposure Booklet enclosed with your radio package.

MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are

trademarks or registered trademarks of Motorola Trademark Holdings, LLC and

are used under license. All other trademarks are the property of their respective

owners.

Printed in Malaysia.

STEP 1

STEP 2

Press +/- button to change channel.

Press +/- button to activate or

deactivate Monitor.

Press +/- button to activate or

deactivate Scan.

Press +/- button to send Call Tone.

*68012000054*

68012000054-C