Epson LABELWORKS PX LW-PX300 Manuel de l'opérateur - Page 12
Parcourez en ligne ou téléchargez le pdf Manuel de l'opérateur pour {nom_de_la_catégorie} Epson LABELWORKS PX LW-PX300. Epson LABELWORKS PX LW-PX300 14 pages.
Également pour Epson LABELWORKS PX LW-PX300 : Manuel de l'utilisateur (2 pages)
Imprimer la page
Troubleshooting
Messages
J
Insert Tape
No tape cartridge is installed. Turn the power off and install a tape
cartridge correctly.
Check tape!
A tape cartridge which cannot be used in this product has been set.
Check the tape cartridge.
Check tape
A tape cartridge which cannot be used in this product has been
cartridge
set. Check the tape cartridge.
Check battery
Possible causes for this message are:
• No power remaining or inserted in the wrong way
• Mixed with other types or old ones
If so, set the batteries correctly or replace them with new ones.
Too many lines
Text entered is too long.
Press
to delete the lines indicated by the cursor.
Text too long
Entered text is too long for the specified tape length. Press
and adjust the tape length or make text shorter.
Seq. num. only 1
Sequence numbers have already been set. Sequence numbers can be
used for one part only.
Problems
J
Does not operate normally.
Initialize this product if it does not operate normally such as the power cannot be
turned on or off, or the display is interrupted.
No image comes out even though
Are the batteries correctly set?
Check if all the batteries are correctly set.
Did the batteries run out?
Replace the batteries with new ones, or use the dedicated AC adapter (APT0615Z2-1).
Is the AC adapter securely connected?
Connect the AC adapter and the power cable firmly to the power socket of the product,
the AC adapter connector and the outlet.
Are you using an AC adapter other than the dedicated one?
Using an AC adapter other than the dedicated one (APT0615Z2-1) is very dangerous, and
may cause overheating or damage to the electric circuits.
Is the display level appropriate?
Adjust the display level.
Display has turned off.
Did you enable the auto power-off function?
The power turns off automatically if no operation is made for more than 5 minutes.
Did you try to carry out a function incorrectly?
If buttons are operated incorrectly, the display turns off for a moment.
Nothing is printed even though
Is text entered?
Nothing is printed if no text is entered.
Any message on the display?
Read the message and take the appropriate action.
Did the tape run out?
Install a new tape cartridge.
Did the batteries run out?
Replace the batteries with new ones, or use the dedicated AC adapter (APT0615Z2-1).
Is the cover on the rear open?
Set the tape cartridge correctly and close the cover completely.
has been pressed.
has been pressed.
Text will be
When creating a label with a special form,
deleted. OK?
current text will be deleted. Press
the special form.
Fill every digit
Entered values for barcodes are wrong. Check the entries about
values, digits, etc.
Load wider tape
Unable to print on the current tape. Use a wider tape.
Text is too long
Entered text is too long for the specified tape length. Press
Continue?
print in the correct length.
Overheated!
The printhead is too hot. Turn the power off and take out the tape
cartridge. Wait for a while before start printing again.
Cover open!
If you open the cover on the rear without turning the power
Powering off.
off, a message is displayed and then the power is turned off
automatically.
Motor error!
An error occurred in the motor operation. Turn the power off once,
then turn it back on. If the same message appears, turn the power
off and contact the K-Sun customer support center.
Characters are not printed properly.
Is the tape cartridge correctly set?
Set the tape cartridge correctly.
Is the printhead dirty?
Clean the printhead.
Did the batteries run out?
Replace them with new ones, or use the dedicated AC adapter (APT0615Z2-1).
Printing ends in the middle of text.
Did the tape run out?
Install a new tape cartridge.
Did the batteries run out?
Replace them with new ones, or use the dedicated AC adapter (APT0615Z2-1).
Created text has gone.
Did you delete the text?
If
+
are pressed, the text on the display will be deleted.
Did you initialize the product?
If the product is initialized, all the created text will be deleted.
Did you remove the batteries or the AC adapter when the product was in operation?
If the AC adapter or the batteries are removed during operation, the text may be deleted.
Cannot attach the label.
Did you peel the backing paper?
Attach the label after peeling the backing paper.
Are you attaching it on a dirty place or on a place with a rough surface?
The label may not adhere due to the material of the attachment location or the
environmental conditions.
to delete the text and show
to
12