Epson 7900p - PowerLite XGA LCD Projector Informations sur le produit - Page 15

Parcourez en ligne ou téléchargez le pdf Informations sur le produit pour {nom_de_la_catégorie} Epson 7900p - PowerLite XGA LCD Projector. Epson 7900p - PowerLite XGA LCD Projector 24 pages. Supplemental / late breaking information
Également pour Epson 7900p - PowerLite XGA LCD Projector : Manuel de l'utilisateur (42 pages), Manuel d'utilisation (36 pages), Pièces de rechange (1 pages), Installation rapide (2 pages), Manuel de l'utilisateur (1 pages), Fiche technique (7 pages), Bulletin d'information sur les produits (7 pages), Lens Installation (5 pages)

Epson 7900p - PowerLite XGA LCD Projector Informations sur le produit

Setting Up the Network

Connect each projector you want to monitor to your network
and configure it with an appropriate IP address.
1. Connect the projector to your network using a
commercially available 100baseTX or 10baseT network
cable. Plug the cable into the projector's Ethernet port.
Ethernet port
To network port
2. Turn on the projector.
3. Press the
button on the remote control and select
Menu
from the
Network
Advanced2
Video
Video
Brightness Control
Brightness Control
Audio
Audio
Projector ID
Projector ID
Effect
Effect
Network
Network
Setting
Setting
COM Port
COM Port
User's Logo
User's Logo
Auto setup
Auto setup
Advanced1
Advanced1
BNC Sync Termination
BNC Sync Termination
Advanced2
Advanced2
Reset
Reset
About
About
Reset All
Reset All
[
[
]: Select
]: Select
[
[
]: Enter
]: Enter
4. If your network assigns addresses automatically, turn on
.
DHCP
5. If your network does not assign addresses automatically,
turn off
and enter the projector's
DHCP
, and
Subnet Mask
Gateway Address
To enter numbers using the remote control, press the
button until it lights, then use the numeric
Num
keypad.
Num button
menu.
:
High
High
Low
Low
: 1
: 1
Set
Set
Select
Set
Set
:
RS-232C
RS-232C
USB
USB
Network
:
ON
ON OFF
OFF
:
ON
ON OFF
OFF
Execute
Execute
[Menu]: Exit
[Menu]: Exit
,
IP Address
, as needed.
Zero
Epson PowerLite 7900p Projector
To change the network addresses from the projector's
control panel, press the right and left arrow buttons to
select the part of the address you want to enter, then
use the up and down arrow buttons to increase or
decrease the numeric value.
Select the part of the
address to change
Note: If you're a network administrator, you can use the
option to enter a trap IP address. This lets you receive
SNMP
trap alerts for the projectors you're monitoring. If you have
HP OpenView, a plug-in is available to allow you to manage
your projectors in HP OpenView. Check with your dealer or
Epson.
When you finish changing an address in the network menu,
press the
button (on the remote control) or the
Enter
button (on the projector). This stores the
Auto/Enter
value.
6. When you're done making all necessary changes, press
to exit the menu system.

Opening and Closing EMP Monitor

To start EMP Monitor, click
Programs > Epson Projector > EMP Monitor
If you've added the program to the Startup programs folder, it
may already be open. If so, click the icon in the system tray on
the lower-right corner of your screen to display the EMP
Monitor window:
To close EMP Monitor, right-click the program icon shown
above, then select
Exit
9/04
Epson PowerLite 7900p Projector
Start > Programs
.
Click here to start EMP Monitor
.
Increase or
decrease
the value
ESC
or
All
15
-